Abstract:In recent years, the addition of Ni has been widely acknowledged to be capable of enhancing the mechanical properties of Al-Si alloys. However, the effect of Ni on the wear behaviors of Al-Si alloys and Al matrix composites, particularly at elevated temperatures, remains an understudied area. In this study, Al-Si-Cu-Mg-Ni/20wt% SiC particles (SiCp) composites with varying Ni contents were prepared by using a semisolid stir casting method. The effect of Ni content on the dry sliding wear behavior of the prepared composites was investigated through sliding tests at 25 and 350°C. Results indicated that the θ-Al 2 Cu phase gradually diminished and eventually disappeared as the Ni content increased from 0wt% to 3wt%. This change was accompanied by the formation and increase in δ-Al 3 CuNi and ε-Al 3 Ni phases in microstructures. The hardness and ultimate tensile strength of the as-cast composites improved, and the wear rates of the composites decreased from 5.29 × 10 −4 to 1.94 × 10 −4 mm 3 /(N·m) at 25°C and from 20.2 × 10 −4 to 7 × 10 −4 mm 3 /(N·m) at 350°C with the increase in Ni content from 0wt% to 2wt%. The enhancement in performance was due to the presence of strengthening network structures and additional Ni-containing phases in the composites. However, the wear rate of the 3Ni composite was approximately two times higher than that of the 2Ni composite due to the fracture and debonding of the ε-Al 3 Ni phase. Abrasive wear, delamination wear, and oxidation wear were the predominant wear mechanisms of the investigated composites at 25°C, whereas delamination wear and oxidation wear were dominant during sliding at 350°C.

Effect of Si Content on the Dry Sliding Wear Properties of Spray-Deposited Al–Si Alloy

A Comparison of the Sliding Wear Behavior of a Hypereutectic Al–Si Alloy Prepared by Spray-Deposition and Conventional Casting Methods

Effect of Fe and Mn additions on microstructure and wear properties of spray-deposited Al–20Si alloy

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Effects of silicon content and test conditions on the dry wear behaviour of Zn–30Al–3Cu–(0–5)Si Alloys

The Effect Of Spray-Formed Al22si Coating On Wear Resistance Performance

Influence of Spray Parameters on Sliding Wear Properties of HVOF Sprayed Fe-Based Amorphous Coatings

Contributions of the Particulate Reinforcement to Dry Sliding Wear Resistance of Rapidly Solidified Al-Ti Alloys

Dry sliding wear of MA/PM Al-10Ti alloy

Wear and Corrosion Properties of 316L-SiC Composite Coating Deposited by Cold Spray on Magnesium Alloy

Wear-resistance mechanism of an Al–12Si alloy reinforced with aluminosilicate short fibers

Influence of Cu content on mechanical and tribological properties of Al–7Si–Cu alloy

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

Microstructure, Mechanical Property and Wear Performance of Cold Sprayed Al5056/SiCp Composite Coatings: Effect of Reinforcement Content

Wear Properties Analysis on Al-Based Automotive Alloy with Varied Levels of Si in Dry, 3.5% NaCl and Seawater Corrosive Environments

Dry Sliding Wear Resistance of the in Situ Al2O3/Al-Si Composites Fabricated in Al-SiO2 by Reaction Hot Pressing

Microstructures and Wear Resistance of Al-25 wt.%Si Coatings Prepared by High-Efficiency Supersonic Plasma Spraying

Microstructure Evolution and Mechanical Properties of Spray-Deposited Al–21. 47Si-4. 73Fe-2. 5Cu-0. 9mg Alloy

Tribological characteristics of new series of Al-Sn-Si alloys

Effect of Different Mg2Si Concentrations on the Wear Properties and Microstructure of Mg2Si/Al–5 wt.% Cu Composites