Abstract:Hypereutectic Al-Si alloys are used as material for the engine block and cylinder liners in automobiles. Wear behaviour of hypereutectic Al-Si alloy system changes significantly with applied normal load in both mild wear and severe wear regime. Significant improvement in wear resistance can be obtained by exposing silicon particles through the chemical etching process. For Al-25% Si alloys, most studies are reported in mild and ultra-mild wear regime. In the present work, the wear of exposed silicon particles with varying load and speed in severe wear regime was investigated under the unidirectional sliding condition and bi-directional sliding condition using a pin-on-disk tribometer (POD) and a linear reciprocating tribometer (LRT), respectively. Rapidly solidified and T6 heat-treated Al-25Si alloy was polished and etched using 5% NaOH solution to expose the silicon particles. Experiments were carried out with normal loads varying from 40 N to 120 N in dry sliding conditions. Sliding speeds of 0.8 m/s and 1.5 m/s were applied for each load in case of a pin on disk tribometer whereas, in an LRT, the sliding velocities were 0.2 m/s and 0.45 m/s respectively for each set of the load. The surface topography was measured by means of a 3-D optical profilometer, and surface morphology was analyzed using SEM images. It was observed that at higher loads, larger Si particles were fractured and pushed into the matrix. Fractured silicon particles, along with smaller particles, were embedded into the matrix, thereby increasing the silicon concentration in the wear region. The comparison of the experimental results of unidirectional and bi-directional sliding that reveal the change in surface morphology of silicon particles, the friction characteristics at the interface, variation of surface 3-D roughness parameters, the wear rate and wear mechanisms of Al-25% Si alloys are analyzed and reported in the study.

A Comparison of the Sliding Wear Behavior of a Hypereutectic Al–Si Alloy Prepared by Spray-Deposition and Conventional Casting Methods

Effect of Si Content on the Dry Sliding Wear Properties of Spray-Deposited Al–Si Alloy

Effect of Fe and Mn additions on microstructure and wear properties of spray-deposited Al–20Si alloy

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Dry sliding wear of MA/PM Al-10Ti alloy

Influence of Spray Parameters on Sliding Wear Properties of HVOF Sprayed Fe-Based Amorphous Coatings

Tribological behaviour of hypereutectic Al-Si automotive cylinder liner material under dry sliding wear condition in severe wear regime

Contributions of the Particulate Reinforcement to Dry Sliding Wear Resistance of Rapidly Solidified Al-Ti Alloys

Wear Behavior of a Heat-Treatable Al-3.5Cu-1.5Mg-1Si Alloy Manufactured by Selective Laser Melting

Wear and Corrosion Properties of 316L-SiC Composite Coating Deposited by Cold Spray on Magnesium Alloy

The effect of squeeze casting process on the microstructure, mechanical properties and wear properties of hypereutectic Al–Si–Cu–Mg alloy

Dry sliding wear of PM Al-10Ti alloy

Dry sliding wear behavior of cast Mg–11Y–5Gd–2Zn magnesium alloy

Sliding wear behavior of high entropy alloy coatings deposited through cold spraying and flame spraying: A comparative assessment

Comparative analysis on high temperature tribological behaviour of additive manufactured and cast AlSi10Mg alloy

Microstructures and Wear Resistance of Al-25 wt.%Si Coatings Prepared by High-Efficiency Supersonic Plasma Spraying

Comparative tribological studies of additive manufactured as-built and chemically polished AlSi10Mg alloy surfaces

Influence of Cu content on mechanical and tribological properties of Al–7Si–Cu alloy

Effects of silicon content and test conditions on the dry wear behaviour of Zn–30Al–3Cu–(0–5)Si Alloys

Microstructural feature dependence of dry sliding wear behaviors in a γ-TiAl alloy