Abstract:Dry sliding wear tests were performed on a Mg–10Y–4Gd–1.5Zn–0.4Zr alloy using a Ball-on-Flat type wear apparatus against an AISI 52100 type bearing steel ball counterface. The wear rates were measured within a load range of 3–25 N, a sliding speed range of 0.03–0.3 m/s and a sliding temperature range of 25–200 °C at a constant sliding distance of 400 m. The morphologies of the worn surfaces and wear debris were studied by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Comparatively, the wear properties of a hypereutectic Al–Si aluminium alloy under the same condition were measured. The results indicate that the wear rates of Mg–10Y–4Gd–1.5Zn–0.4Zr alloy are lower than that of cast+T6 AC9B aluminium alloy. The dominant mechanism of cast+T6 Mg–10Y–4Gd–1.5Zn–0.4Zr alloy is abrasion wear mixed with other wear mechanisms, which tends to be an abrasion and plastic deformation wear at high normal load such as 10–25 N, abrasion and plastic deformation wears with small participation of delamination and oxidative wears at high sliding speed such as 0.12–0.3 m/s, and an oxidative and abrasion wear at high test temperature such as 100–200 °C. The Mg12Y1Zn1 phase in Mg–10Y–4Gd–1.5Zn–0.4Zr alloy plays an important role in the wear rate.

Dry sliding wear of MA/PM Al-10Ti alloy

Dry sliding wear of PM Al-10Ti alloy

Microstructure and Sliding Wear Behavior of PM Alloy Al10Ti after Thermal Exposure

Contributions of the Particulate Reinforcement to Dry Sliding Wear Resistance of Rapidly Solidified Al-Ti Alloys

Effect of Cold Deformation on Low Speed Sliding Wear of Al-10Ti Alloy

Dry Sliding Wear Behavior of Ti-6Al-4V Alloy in Air

Dry Sliding Wear of a Ti50Ni25Cu25 Particulate-Reinforced Aluminum Matrix Composite

Effects of cold deformation on the low speed sliding wear of the RS/PM Al–10 wt.% Ti alloy against carbon steel

Effects of second phase on dry sliding wear of rapidly solidified Al-Ti alloy

Sliding Wear Behavior of Forged, Uncoated and Laser Nitrided LMD TC18 Titanium Alloy

Wear Characteristics of a Rapidly Solidified Al-Si Alloy under Dry Sliding

Dry Sliding Wear Behavior Of Hot-Dip Aluminized Ti-6al-4v Alloy Against Gcr15 Steel

Wear behavior of Mg–10Y–4Gd–1.5Zn–0.4Zr alloy

Mechanisms of remarkable wear reduction and evolutions of subsurface microstructure and nano-mechanical properties during dry sliding of nano-grained Ti6Al4V alloy: A comparative study

Sliding Wear Behavior of Laser-Nitrided and Thermal Oxidation-Treated Ti–5Al–5Mo–5V–1Cr–1Fe Alloy Fabricated by Laser Melting Deposition

Dry Sliding Friction and Wear Characteristics of T6 Treated Al-10Si-5Cu-0.75Mg Alloy

Study on Dry Friction and Wear Properties of TiAl Alloy

Dry sliding wear behavior of Fe3Al alloys prepared by mechanical alloying and plasma activated sintering

Correlation between the characteristics of the thermo-mechanical mixed layer and wear behaviour of Ti–6Al–4V alloy

Dry sliding wear of Ti-6Al-4V alloy in air and vacuum

Dry Sliding Wear Behaviour of Mg–10Gd–3Y–0.4Zr Alloy