Abstract:The solutionizing temperature effect on the dry sliding wear performance of cast T 6 heat-treated Al–Si–Mg-Ni hypoeutectic alloy is explored in this work. The alloys were melted and transferred into a pre-heated metallic die using an electric furnace to produce cast rods of ɸ 32 mm × 150 mm in length. The cast alloys were solutionized for 8 h at 450 °C & 540 °C and quenched in water at 30 °C. Furthermore, a 12-h artificial ageing procedure was carried out at 180 °C. Hardness and tribological behaviour for the cast heat-treated rods were evaluated using the Vickers microhardness tester and a pin-on-disk tribometer. The wear test was conducted on the samples for varying loads (5, 8 and 10N) and sliding velocity (0.1, 0.15, 0.2 m/s). It was noted that the hardness value increased from the baseline alloy to the Al–Si–Mg-3Ni alloy subjected to heat treatment at 540 °C. It was also found that when the solutionizing temperature was enhanced, there was a decrease in the value of the specific wear rate and friction coefficient. Moreover, adding 3 wt% of nickel substantially improved the sliding wear performance. The presence of intermetallic such as Al 3 Ni during Ni additions to Al–Mg-Si alloy and spheroidization of silicon, precipitation of intermetallic and eutectic phases during ageing treatment played an essential role in improving the hardness and sliding wear performance. Advanced characterization techniques were used to evaluate the microstructure, wear track, tribo layer, and wear debris and to analyze the wear mechanism of the heat-treated wear test samples.

Dry Sliding Friction and Wear Characteristics of T6 Treated Al-10Si-5Cu-0.75Mg Alloy

Influence of heat treatment on microstructure and friction and wear properties of multicomponent Al-7·5Si-4Cu alloy

Dry sliding wear of MA/PM Al-10Ti alloy

Effect of Heat Treatment on Mechanical Properties, Microstructures and Wear Resistance of Al-Si-Cu Alloy

Dry Sliding Wear Behavior of Ti-6Al-4V Alloy in Air

Effects of Loading and Sliding Speed on the Dry Sliding Wear Behavior of Mg-3Al-0.4Si Magnesium Alloy

Dry sliding wear of PM Al-10Ti alloy

Wear Behavior of a Heat-Treatable Al-3.5Cu-1.5Mg-1Si Alloy Manufactured by Selective Laser Melting

Correlation between the characteristics of the thermo-mechanical mixed layer and wear behaviour of Ti–6Al–4V alloy

Microstructure and Sliding Wear Behavior of PM Alloy Al10Ti after Thermal Exposure

Solutionizing Temperature Effect on the Dry Sliding Wear Performance of Al-7Si-0.3Mg-3Ni Hypoeutectic Alloy

Dry sliding wear behavior of cast Mg–11Y–5Gd–2Zn magnesium alloy

Dry Sliding Wear Behavior Of Hot-Dip Aluminized Ti-6al-4v Alloy Against Gcr15 Steel

Wear behavior of Mg–10Y–4Gd–1.5Zn–0.4Zr alloy

Tribological Behaviour of Al18B4O33-whisker-reinforced Hypoeutectic Al–Si–Mg-matrix Composites under Dry Sliding Conditions

Wear and Frictional Behavior of Copper Modified Ti-6Al-4V Alloy

Dry Friction Characteristics of Ti-6Al-4V Alloy under High Sliding Velocity

Dry Sliding Wear Behavior of Hot-Dip Aluminized Ti-6Al-4V Alloy As a Function of Sliding Velocity

The Effect of Applied Load and Rotation Speed on Wear Characteristics of Al-Cu-Li Alloy

Dry wear behavior of rheo-casting Al–16Si–4Cu–0.5Mg alloy

Study on Friction and Wear Characteristics of Die Casting Magnesium Alloy AZ91D