Abstract:The microstructural characteristics and morphological attributes of the target material, along with its intrinsic properties, can significantly influence the performance of the resultant film. Currently, commercially available nickel-vanadium targets employed in the industry have not been subjected to investigations aimed at controlling grain size and grain orientation. This study examines the effects of unidirectional rolling at room temperature, combined with substantial deformation, on the alterations in microstructure, texture evolution, and mechanical properties of the NiV7 alloy. The process of severe plastic cold rolling leads to a continuous elongation and refinement of the grains. The changes in microstructure and texture of the cold-rolled sheets were analyzed using electron backscatter diffraction (EBSD) technology. At an 80% reduction, a significant number of sub-grains are observed, which transform into deformed grains as the reduction reaches 95%. With a thickness reduction of 96.6%, the average grain size is approximately 1.10μm. Further increases in reduction do not lead to significant alterations in the grain structure; instead, the grain orientation progressively becomes more uniform with higher levels of deformation. The combination of substantial deformation and lower rolling rates results in an increased number of high-angle grain boundaries. The alloy displays various textures throughout the rolling process, including S-type, copper-type, brass-type, fiber, and cubic textures. Notably, the prevalence of S-type and fiber textures diminishes as the degree of deformation increases, while the cubic texture becomes increasingly prominent. Upon achieving a reduction of 95%, the cubic texture emerges as the dominant texture. A transmission electron microscope (TEM) was utilized to examine the extensive array of dislocations, dislocation cells, dislocation walls, and shear bands generated during the cold rolling process. At a deformation level of 96.6%, the ultimate tensile strength of the alloy demonstrates a significant enhancement, attributed to mechanisms of dislocation strengthening and grain strengthening, reaching a value of 1231±20 MPa, accompanied by a post-fracture elongation of approximately 2%. The ultimate tensile strength exhibited an increase of 781±20 MPa compared to the sample prior to the rolling process; however, there was a notable reduction in plasticity.

Microstructure and Tensile Properties of Ultrafine-Grained Ni-Based Alloy Prepared by Severe Deformation Rolling

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Achieving High Strength and Tensile Ductility in Pure Nickel by Cryorolling with Subsequent Low-Temperature Short-Time Annealing

Severe plastic cold rolling effects in Nickel-Vanadium alloy: Microstructure, texture evolution and mechanical properties

Effect of Cold Rolling on the Microstructure and Mechanical Behaviors of High-Nitrogen and Low-Nickel Alloy

Effect of caliber rolling on microstructures and properties of an inoculated Cu–Al–Ni shape memory alloy

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Significant annealing-induced hardening effect in nanolaminated-nanotwinned (CrCoNi)97.4Al0.8Ti1.8 medium-entropy alloy by severe cold rolling

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

Microstructure and Tensile Properties of Al0.5CoCrCuFeNi Alloys Produced by Simple Rolling and Annealing

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Effect of Annealing on the Microstructure, Texture, and Properties of Cold-Rolled Ti50Ni47Fe3 Shape Memory Alloy Sheets

Research on Effects of Rolling-Drawing Deformation on Performance of Cu-10Ni-1Fe-1Mn Alloy

Grain Growth Mechanism of Lamellar-Structure High-Purity Nickel via Cold Rolling and Cryorolling during Annealing

Effect of cold rolling on microstructure and mechanical properties of pure Zr

Effect of room temperature rolling and annealing on microstructure and mechanical properties of (CrCoNi) 96 V 4 medium entropy alloy

Effect of Annealing and Double Aging on the Microstructure and Mechanical Properties of Hot-Rolled Al17Cr10Fe36Ni36Mo1 Alloy

Microstructure and Mechanical Properties Evolution of the Al, C-Containing CoCrFeNiMn-Type High-Entropy Alloy during Cold Rolling

Effect of Deformation Degree on Microstructure and Properties of Ni-Based Alloy Forgings

Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures

Evolution of microstructure and mechanical properties influenced by nanosized precipitates during rolling deformation