Abstract:A systematic study was conducted on the impact of annealing treatments on the microstructure and properties of cold-rolled Ti50Ni47Fe3 alloys using optical microscopy, scanning electron microscopy, electron backscattered diffraction, and an electronic universal testing machine. It was found that, during low-temperature annealing (400 °C and 500 °C), the annealing time had no significant effect on the microstructure or properties of the Ti50Ni47Fe3 alloy. Only elongation (δ) increased with the increase in the annealing time, and the grain orientation of the Ti50Ni47Fe3 alloy was //RD (rolling direction). When annealing at medium–high temperature (600 °C), as the annealing time increased, recrystallization and grain growth processes occurred, resulting in a continuous decrease in strength and an increase in δ. Meanwhile, it was found that the grain orientation of the cold-rolled Ti50Ni47Fe3 alloy changed from //RD during the recovery and recrystallization processes to //RD after the grain growth process. The orientation distribution function cross-section φ2 = 45° results indicate that the texture was mainly distributed along the γ orientation line (φ1 = 0~90°, Φ = 54.7°, φ2 = 45°). When annealed at 400 °C and 500 °C, the texture of the Ti50Ni47Fe3 alloys was (111)[uvw]. When the annealing treatment was 600 °C for 120 min, a (110)[uvw] texture occurred. Additionally, ductile fracture occurred in all specimens, and the crack origin was located on one side of the fracture surface, with obvious "Y"-shaped propagation. This article studied annealing treatments of cold-rolled Ti50Ni47Fe3 alloys, providing corresponding theoretical guidance for subsequent production applications.

Effect of caliber rolling on microstructures and properties of an inoculated Cu–Al–Ni shape memory alloy

Effect of combined use of inoculation and hot rolling on microstructures and damping property of a Cu-Al-Ni-Mn-Ti shape memory alloy

Effects of grain refinement on the microstructures and damping behaviors of a Cu–Al–Ni–Mn–Ti shape memory alloy

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Refining effect of an intermetallic inoculant on a Cu–Al–Mn shape memory alloy

Effect of pack rolling on microstructures and tensile properties of as-forged Ti-44Al-6V-3Nb-0.3Y alloy

Microstructural Evolution and Mechanical Properties of Pure Aluminum upon Multi-Pass Caliber Rolling

Influence of Different Rolling Processes on Microstructure and Strength of the Al–Cu–Li Alloy AA2195

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Effects of Rolling Deformation on Precipitation Behavior and Mechanical Properties of Al–Zn–Mg–Cu Alloy

Effect of Annealing on the Microstructure, Texture, and Properties of Cold-Rolled Ti50Ni47Fe3 Shape Memory Alloy Sheets

Research on Effects of Rolling-Drawing Deformation on Performance of Cu-10Ni-1Fe-1Mn Alloy

Evolution of microstructures and properties of Ti-44Al-6V-3Nb-0.3Y alloy after forging and rolling

Effects of Cold Rolling Reduction Rate on the Microstructure and Properties of Cu-1.16Ni-0.36Cr Alloy after Thermo-Mechanical Treatment

Effects of Rolling Deformation on Microstructure and Hardness of Ti-45Al-9Nb-0.3Y Alloy

Effect of Rolling Strain on Microstructure and Tensile Properties of Dual-Phase Mg–8Li–3Al–2Zn–0.5Y Alloy

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Effects of intermediate annealing and rolling on plastic failure and grain refinement of Al-Mg-Li alloy

Microstructure and Tensile Properties of Ultrafine-Grained Ni-Based Alloy Prepared by Severe Deformation Rolling

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy