A CMOS High-Speed Sample-and-Hold Amplifier

薛亮,沈延钊,张向民

DOI: https://doi.org/10.3969/j.issn.1004-3365.2004.03.024

2004-01-01

Abstract:The fundamental theory of the sample and hold circuit is analyzed, and a CMOS high-speed sample-and-hold amplifier is designed, for which a sampling rate of 50 Msample/s has been achieved. The circuit, as well as its blocks, is simulated, in TSMC 's 0.35 μm standard CMOS process using Hspice.

What problem does this paper attempt to address?

Design of a High-Speed Sample-and-hold Circuit Using a Substrate-Biasing-effect Attenuated T Switch

Koubao Ding,Kunming Cai,Yan Han

DOI: https://doi.org/10.1016/j.mejo.2010.06.018

IF: 1.992

2010-01-01

Microelectronics Journal

Abstract:A circuit technique for designing a high speed sample-and-hold circuit is proposed. A substrate-biasing-effect attenuated T switch is used during the hold mode of sample-and-hold circuit, the T type structure makes the input-dependent signal feed-through effect neglectable, and a high linearity performance can be assured. Based on SMIC 0.13μm Standard CMOS process, a sample-and-hold circuit applicable to 12bit, 100MHz Pipelined ADC is designed. Spectre simulation results show that the using this technique can improve the dynamic performance and the signal-to-noise and distortion ratio (SNADR) and spurs free dynamic range (SFDR) of the sample-and-hold circuit is 85.5 and 92.87dB, respectively, under the Nyquist input frequency .
Design of a Sample-and-Hold Circuit for High Speed CMOS Image Sensor

CAI Kunming,DING Koubao,LUO Hao,HAN Yan

DOI: https://doi.org/10.3969/j.issn.1004-1699.2010.07.015

2010-01-01

Abstract:A sample-and-hold circuit utilized in high speed integrator array is designed. A new T type switch which can restrain the substrate biasing effect is designed to replace the traditional CMOS transmission gate switch. Thus, the linearity of the switch’s turn-on resistance can be assured because the changes of threshold voltage caused by the substrate biasing effect is limited. Also,this new T type structure can reduce the charge feed through effect under high frequency input,thus,a better turn-off isolation characteristic can be achieved . Based on SMIC 0. 13 μm Standard CMOS technique,a sample-and-hold circuit applicable to the CMOS image sensor is designed. Spectre simulation results show that the Signal-to-Noise Distortion Ratio and Spurs Free Dynamic Range is 85. 5 dB and 92. 87 dB respectively under the Nyquist input frequency,the power consumption is only 32. 8 mW.
Optimization Of Sample/Hold Circuit For High-Speed And High-Resolution Adcs

Junxiao Chen,Lu Zhang,Lenian He

2009-01-01

Abstract:A sample/hold (S/H) circuit for a 14 bit 100 MSample/s analog-to-digital converter is implemented and optimized. High performance gain-boosted folded-cascode opamp (GBFCA) and bootstrapped switches are used to maximize SNDR and SFDR of the S/H circuit. An optimal design criterion is developed to find the best solution giving the shortest settling time. After eliminating the slow-settling component in signal path, the sample S/H circuit achieves 5ns settling time to 0.001%, 81.2 dB SNDR and 100 dB SFDR for 10 MHz input signals.
A CMOS high performance 50MS/s sample/hold circuit

LI Tie,GUO Li,BAI Xue-Fei

2007-01-01

Abstract:A high performance CMOS sample/hold circuit is presented,which achieves the precision of 10bit over Nyquist band in 50MHz sampling frequency at 3.3V supply.This circuit uses full differential circuits,bottom-plate sampling,bootstrap circuits and a high performance gain-boost operational amplifier.Simulation in 0.35μm CMOS process shows the circuit consumes 18mW of power.
High-Speed Operational Amplifier Based on 0.5 Μm CMOS Process

葛康康,陈琛,何乐年

DOI: https://doi.org/10.3969/j.issn.1671-7147.2008.06.005

2008-01-01

Abstract:A design methodology of high-speed operational amplifier(Op-amp) with high frequency of unity-gain bandwidth,high slew rate and large output swing is proposed.The structure with two-stage fully differential CMOS circuit was used in the op-amp,and the non-dominant pole was canceled by using a zero in left plane which is produced by adding a feed-forward amplify circuit.Moreover,obtain high stability of the common-mode,a novel CMFB structure is used.As a result,the value of CMRR was increased to be 62 dB.The chip is implemented by using CSMC 0.5 μm CMOS mixed-signal technology.The measurement results indicate that under the condition of supplied voltage of 3.3 V,the op-amp gets a DC voltage gain of 65.5 dB,unity-gain bandwidth of 350 MHz and output swing of ±2.7 V.
A Low Power Sample-and-Hold Circuit for Pipelined A/D Converter

Lenian He

IF: 1.992

2005-01-01

Microelectronics Journal

Abstract:A low power sample-and-hold circuit for a 10-bit 20 MS/s pipelined A/D converter has been designed,which is implemented in a 0.6 μm double-poly double-metal CMOS process.The S/H circuit is realized in switched-capacitor topology.Differential signal input topology is used to make the circuit less sensitive to interference.A common-mode feedback circuit is also used to stabilize the common-mode output to a desired level,thus improving the precision of the S/H.Furthermore,the S/H circuit consumes only 5 mW power at 5 V supply voltage with a low power operational transconductance amplifier(OTA).The A/D converter based on this S/H circuit achieves a SNDR of 58 dB at 20 MHz sampling rate,and the power dissipation is only 49 mW.
A sample and hold circuit for high speed ADCs

CAI Kun-ming,DING Kou-bao,LUO Hao,HAN Yan

DOI: https://doi.org/10.3969/j.issn.1007-0249.2010.03.007

2010-01-01

Abstract:A sample and hold circuit used in the front end of Pipelined ADCs is designed. The performance index of all the sub-circuit are analyzed from the requirement of 12 bit,100MHz Analog-to-Digital Converters theoretically, and then the sub-circuit such as gain-boosted OTA、bootstrap switch is designed according to the above requirements. Base on SMIC 0.13μm, 3.3V technique, Spectre simulation shows that SINAD, SFDR and ENOB can reach 81.9dB, 94.9dB, and 13.3bit respectively,with only 24mw power consumption. Even the input signal is up to Nyquist frequency, its SINAD and SFDR can still keep 81.5dB and 92.67dB along with the 13.2bit ENOB.
A High Performance CMOS Sample and Hold Circuit

Liu Minjie,Chi Baoyong,Liu Yunfeng,Dong Jingxin

DOI: https://doi.org/10.3969/j.issn.1671-4776.2009.11.012

2009-01-01

Abstract:A high performance sample and hold circuit with the full differential capacitor flip-around architecture,which decreased the noise and power consumption efficiently,was presented.In the circuit design,the new gate voltage bootstrapped switch for constant Vgs was used to reduce significantly nonlinear distortion,and DC drift of the input signal was effectively rejected.It was implemented by 0.18 μm 1P-6M CMOS twin-well process,and an 86.88 dB spurious-free dynamic range(SFDR)and a 73.50 dB peak signal-to-noise plus distortion ratio(SNDR)over the first Nyquist band were obtained with a sampling rate of 32 MHz and a single 1.8 V power supply.Finally,the layout of the circuit and first test waveform of the chip were presented.The result shows the circuit realizes the function of sample and hold.
Design of Charge Pump for High-Speed Phase-Locked Loop

温显光,解宁,何乐年,徐新民,孙振国

DOI: https://doi.org/10.3969/j.issn.1000-7180.2004.12.054

2004-01-01

Abstract:A novel structure of a charge pump for high-speed Phase-Locked Loop (PLL) is presented. The design is based on 0.25um CMOS mixed-signal process of TSMC. Positive feedback and supply-independent biasing are used to solve charge injection effect and to obtain faster switching speed. Simulation results show that the charge pump meets the need of 480 MHz PLL circuit entirely.
High-speed and high-gain operational amplifier

ZHU Ying,HE Le-nian,YAN Xiao-lang

DOI: https://doi.org/10.3969/j.issn.1007-0249.2008.02.007

2008-01-01

Abstract:A high-speed and high-gain operational amplifier is presented in this paper.The op-amp design achieves gain improvements through the addition of two auxiliary op-amps using fully differential common source common gate circuits.In addition,frequency response characteristics are improved through the use of frequency compensation capacitors and clamp transistors,yielding transient frequency response performances that closely matches the response of single-pole op-amp and the added benefit of much faster settling time.Simulations with SMIC's 0.35μm process model shows the new op-amp's DC gain is higher than 110dB with a bandwidth of 266MHz(1～pF load),and 55° phase margin.The op-amp only needs 10ns to achieve 0.1% settling accuracy.It is a practical high-speed and high-precision op-amp design.
A High-Speed High-Resolution Sample-and-Hold Circuit

Yang Bin,Yin Xiumei,Yang Huazhong

DOI: https://doi.org/10.3969/j.issn.1674-4926.2007.10.029

2007-01-01

Chinese Journal of Semiconductors

Abstract:A high performance CMOS sample and hold (S/H) circuit for use in the front end of a 12bit 100MS/s ADC is presented.It achieves a 108dB spurious-free dynamic range and 77dB signal-to-noise ratio over the Nyquist band at a 100MHz sampling frequency with a 3V power supply.An analysis model for the S/H circuit is built to capture the switching effect.The impact of the switches’ arrangement is also addressed.The leakage in a conventional bootstrapped switch is analyzed and some improvements are made,enhancing the linearity significantly.
A 12-Bit 200-Ms/s Sample-and-hold Amplifier with a Hybrid Miller-Feedforward Compensation Technique

Yongzhen Chen,Chixiao Chen,Qiang Zhang,Fan Ye,Junyan Ren

DOI: https://doi.org/10.1109/asicon.2013.6811866

2013-01-01

Abstract:A CMOS fully differential high gain-bandwidth (GBW) operational amplifier applied in a sample-and-hold (S&H) circuit is presented in the paper. High bandwidth and phase margin of the amplifier are obtained by combining two compensation techniques: Miller compensation and Feedforward compensation. In addition, in order to achieve a high gain, the gain-boosting technique is employed. The circuit is designed in SMIC 65 nm process consuming 47.25 mW at a 1.2 V power supply and is suitable for 12-bit 200-MS/s pipelined ADC applications. At 200 MS/s, the S&H circuit achieves 77.68 dB SNDR for an input of 92.38 MHz.
A CMOS High-Speed Multistage Preamplifier for Comparator Design

XP Fan,PK Chan

DOI: https://doi.org/10.1109/iscas.2004.1328252

2004-01-01

Abstract:A new multistage preamplifier with offset reduction for use in high-speed comparator is presented. The proposed circuit is based on the cascade of the modified input offset storage amplifiers and the output offset storage amplifier in pipeline arrangement. Not only does the topology maintain a good input common-mode range, it exhibits faster speed due to reduced capacitive loads. Using AMS 0.35mum CMOS process model, the simulation result has shown that the new preamplifier has achieved a settling time of 3.5 ns at 1% accuracy for a transient step of 400 mV, which is faster than the conventional works at identical process and identical power consumption.
A 10-bit 20-Msample/s 49mW CMOS pipelined A/D converter

Tang Yongjian,Lenian He,Ning Xie,Xi Chen,Kun Yin,Xiaolang Yan

DOI: https://doi.org/10.1109/icsict.2004.1436903

2004-01-01

Abstract:A 10-bit 20-Msample/s CMOS pipelined analog-to-digital converter (ADC) is proposed, which is implemented in a 0.6/spl mu/m double-poly double-metal CMOS process. The digital correction technique is used to relax the offset requirement of the comparators. To reduce signal-dependent charge injection and substrate noise injection, the bottom-plate sampling technology is applied. A sample-and-hold amplifier (SHA) is also used to improve the signal-to-noise and distortion ratio (SNDR) performance and the linearity of ADC. The circuit is simulated by the Hspice software which is based on CSMCs library of 0.6/spl mu/m mixed-signal CMOS model. The simulation results reveal that the ADC designed with this method achieves the SNDR of 58dB at full speed of 20MHz when input frequency is 5MHz. Furthermore, the ADC consumes 49mW power at 5V supply voltage with a low power operational transconductance amplifier (OTA) and the dynamic comparators.
Design of a High-Speed Flip-Around Sample-and-Hold Circuit

YAO Ruo-he,ZHU Jian-pei,WU Wei-jing,ZHANG Wei-hua

DOI: https://doi.org/10.3969/j.issn.1004-3365.2006.02.025

2006-01-01

Abstract:Major factors affecting the performance of flip-around sample-and-hold circuit are analyzed.A bootstrapped switch with dummy transistor is used to reduce the signal-dependent charge injection and clock feedthrough.The gain boost technique is used to enhance the DC gain of the main opamp,and the best transient performance has been achieved by adjusting the load capacitances of the auxiliary amplifiers.A flip-around sample-and-hold circuit based on these techniques has been designed and simulated in TSMC′s 0.25 μm CMOS process.Simulation results show that the sample-and-hold circuit has a good performance.
A 32.5-GS/s two-channel time-interleaved CMOS sampler with switched-source follower based track-and-hold amplifier

Shunli Ma,Jiacheng Wang,Hao Yu,Junyan Ren

DOI: https://doi.org/10.1109/MWSYM.2014.6848369

2014-01-01

Abstract:This paper presents a high speed and low distortion sampler with two-channel time-interleaved sampler with track-and-hold amplifier (THA). The THA is based on switched source-follower with active inductor load such that wide bandwidth in tack-mode and small signal feed-through in hold-mode can be both achieved within compact area. Furthermore, one clock-controlled auxiliary transistor is also introduced to cancel clock feed-through in hold-mode. The chip was fabricated in 65nm RF-CMOS process with core area of 0.07mm2 and power consumption of 192mW. The measured S-parameters show matched input and output up to 40GHz with 19.3GHz bandwidth in track-mode. The measured spurious-free-dynamic-range (SFDR) is 35dB, and total harmonic distortion (THD) is -30dB sampled at 16.26GS/s in one channel.
A 32.5-Gs/s Sampler with Time-Interleaved Track-and-Hold Amplifier in 65-Nm CMOS

Shunli Ma,Hao Yu,Junyan Ren

DOI: https://doi.org/10.1109/tmtt.2014.2366121

IF: 4.3

2014-01-01

IEEE Transactions on Microwave Theory and Techniques

Abstract:This paper presents a high-speed and low feed-through sampler with two-channel time-interleaved track-and-hold amplifiers (THAs). The THA is based on switched buffer with active inductors load such that wide bandwidth in track-mode and small-signal feed-through in hold-mode can be both achieved within compact area. Furthermore, one clock-controlled auxiliary transistor is also introduced to cancel clock feed-through in hold-mode. With two-channel accurate on-chip clock and its distribution network, double sampling rate is achieved due to the two-channel time-interleaved structure used. The chip was fabricated in 65-nm RF-CMOS process with core area of 0.07 mm 2 and power consumption of 211 mW. The measurements show that the S-parameters matched input and output up to 40 GHz with 19.3-GHz bandwidth in track-mode, the spurious-free-dynamic-range above 35 dB and total harmonic distortion below -30 dB up to 6 GHz when the sampling rate is 16.26 GS/s for one channel.
An Undersampling High-Resolution Low-Power Sample-and-Hold Circuit

YE Fan,XU Jun,LI Lian

DOI: https://doi.org/10.3969/j.issn.1004-3365.2006.06.025

2006-01-01

Abstract:An undersampling high resolution low power sample-and-hold circuit is presented,which achieves a resolution over 11 bits at 90 MHz input frequency and 40 MHz sampling rate.A flip-around S/H circuit is used to eliminate the capacitor mismatch,and a gate-voltage bootstrapped switch is adopted for improved linearity.The undersampling condition could be realized.A high-gain large-bandwidth low-power gain-boost telescopic cascode amplifier is designed.Implemented in 0.35 μm CMOS process,the circuit operates at 3.3 V supply voltage with only(7.6 mW) of power dissipation.
An 18-GHz-bandwidth master-slave sample-and-hold amplifier for high-speed communication in 0.13um SiGe BiCMOS

Hao Ding,Jian-Ye Wang,Wei Liu,Yong-Zhong Xiong

DOI: https://doi.org/10.1109/IEEE-IWS.2018.8400884

2018-01-01

Abstract:Design and analysis of a fully-differential master-slave sample-and-hold amplifier (SHA) is presented in this paper using 0.13um SiGe BiCMOS process. To achieve broad bandwidth, Cherry-Hooper topology is employed in the input buffer of SHA. With feedthrough-attenuation capacitors and clock-controlled auxiliary transistors in track-hold switch, signal feed-through and clock feedthrough are reduced. To shorten trackhold transition time, sinusoidal clock signal is converted to square wave in clock buffer. Input bandwidth of 18GHz, spurious free dynamic rang above 33dB are measured for 2 GSample/s and -5dBm single-ended input signal. The proposed SHA is suit for high-speed high-broadband analog-to-digital converter used in high-speed wireless communication.
A 1.2V Sample-and-Hold Circuit for 14-Bit 250MS/s Pipeline ADC in 65nm CMOS

wang xuan,li fule,wu bin

DOI: https://doi.org/10.1007/978-3-642-27966-9_69

2012-01-01

Abstract:This paper presents a design of a high speed, high accuracy. low voltage sample and hold circuit used in pipeline analog to digital converter for wireless communication applications in 65nm CMOS technology. Due to the low intrinsic gain of 65nm process, an OTA with simplified class A/B output stage and gain-boosting technique is introduced in the circuit, acquiring a gain of more than 80dB, so as to achieve a 14-bit linearity and a rail-to-rail output swing as well with low power consumption. The linearity issue of the switches is also taken into consideration. The simulation result shows a maximum SFDR of 96.3dB at 11MHz, 95.0dB at 149MHz and 87.1dB at 405MHz input frequency under a sampling rate of 250MS/s.

A CMOS High-Speed Sample-and-Hold Amplifier

Design of a High-Speed Sample-and-hold Circuit Using a Substrate-Biasing-effect Attenuated T Switch

Design of a Sample-and-Hold Circuit for High Speed CMOS Image Sensor

Optimization Of Sample/Hold Circuit For High-Speed And High-Resolution Adcs

A CMOS high performance 50MS/s sample/hold circuit

High-Speed Operational Amplifier Based on 0.5 Μm CMOS Process

A Low Power Sample-and-Hold Circuit for Pipelined A/D Converter

A sample and hold circuit for high speed ADCs

A High Performance CMOS Sample and Hold Circuit

Design of Charge Pump for High-Speed Phase-Locked Loop

High-speed and high-gain operational amplifier

A High-Speed High-Resolution Sample-and-Hold Circuit

A 12-Bit 200-Ms/s Sample-and-hold Amplifier with a Hybrid Miller-Feedforward Compensation Technique

A CMOS High-Speed Multistage Preamplifier for Comparator Design

A 10-bit 20-Msample/s 49mW CMOS pipelined A/D converter

Design of a High-Speed Flip-Around Sample-and-Hold Circuit

A 32.5-GS/s two-channel time-interleaved CMOS sampler with switched-source follower based track-and-hold amplifier

A 32.5-Gs/s Sampler with Time-Interleaved Track-and-Hold Amplifier in 65-Nm CMOS

An Undersampling High-Resolution Low-Power Sample-and-Hold Circuit

An 18-GHz-bandwidth master-slave sample-and-hold amplifier for high-speed communication in 0.13um SiGe BiCMOS

A 1.2V Sample-and-Hold Circuit for 14-Bit 250MS/s Pipeline ADC in 65nm CMOS