Abstract:Jet fuel is used as a coolant before it is burned in the combustor of the aircraft. Insoluble particles and surface deposits can impair engine performance. Jet fuel thermal oxidation test (JFTOT) defines the standard test method for evaluation of the deposit formed through heating fuels in tubes caused by thermal oxidation (<400°C). At a higher temperature, fuel in the heating process decomposes leading to surface deposits by coking. In this work, we propose a method to evaluate the security of fuel flowing in the tube at high temperatures (>500°C). The heat transfer and cracking performances of two hydrocarbon fuels which are laboratory modified aviation kerosene (Fuel 1 (ρ=0.85g/cm3) and Fuel 2 (ρ=0.78g/cm3)) have been investigated in a heat-exchanger under supercritical conditions (T=700–770°C, p=2.5–5.5MPa, m=0.4–1.0g/s). The temperature and flow rate in this work are much higher than those in JFTOT. The safe run time (SRT) is used to evaluate the heat transfer security of each fuel. As the temperature increases or the flow rate decreases or the pressure increases, the SRTs of Fuel 1 and Fuel 2 decrease clearly. In general, the heat transfer security of Fuel 1 is better than that of Fuel 2. Moreover, the volumetric heat sink of Fuel 1 is larger than that of Fuel 2. So, the overall performance of Fuel 1 is more excellent when it is used as propellant and coolant for hypersonic aircraft. In consideration of the heat transfer security, heat sink and the required driving force for aircraft, the temperature of fuel at the exit of heat transfer passage should be set as 740°C, the flow rate of fuel should be 0.6–1.0g/s, the pressure of heat transfer passage should be 3.5MPa. Based on these results, we find that the modification of a high density fuel is an effective way to prepare an advanced hydrocarbon fuel.

Study on thermal capacity of endothermic hydrocarbon fuel by high-temperature calorimeter

MEASUREMENT OF HEAT SINK FOR ENDOTHERMIC FUELS

BUILDING OF ENDOTHERMIC FUEL COOLING SIMULATION SYSTEM

Design and Application of a Thermal Characteristic Test Platform for Hydrogen Fuel Cells

Measurements of Isobaric Heat Capacity of R143a and R227ea at Liquid Phase by Quasi-Steady Scanning

Distributed Flow Calorimetry With Wide Temperature and Pressure Range Based on Scanning Radiation Thermometry

A New Flow Calorimeter For The Determination Of The Isobaric Heat-Capacity Of Vapors

Measurements of Coefficient of Convective Heat Transfer for Endothermic Hydrocarbon Fuel Up to Supercritical Pressures

Thermal Cracking and Heat Sink Measurement of Model Compounds of Endothermic Hydrocarbon Fuels under Supercritical Conditions

Nuclear Magnetic Resonance Determination And Gas Chromatography/Mass Spectrometric Analysis Of Endothermic Hydrocarbon Fuels Along With Thermodynamic Property Prediction

A fluid temperature interpolation method for wide temperature range distributed flow calorimeter

Measuring enthalpy of fast exothermal reaction with micro-reactor-based capillary calorimeter

Experimental Investigation on Thermal-Hydraulic Characteristics of Endothermic Hydrocarbon Fuel in 1 Mm and 2 Mm Diameter Mini-Channels

A Quantum Chemistry Study on Thermochemical Properties of High Energy-Density Endothermic Hydrocarbon Fuel JP-10

Experimental measurements on chemical reaction and thermal conductivity of the H<sub>2</sub>/CO<sub>2</sub>/CO/CH<sub>4</sub>/H<sub>2</sub>O system using the short-hot-wire method at 664-915 K and 9.2-22.2 MPa

Calorimetric Determination of the Vapor Heat Capacity of Petroleum Cuts

Molar excess enthalpies of ethyl acetate+alkanols at T=298.15K, p=10.0MPa

Accurate heat capacity determination of solids and liquids using a heat conduction calorimeter

Heat Transfer and Cracking Performance of Endothermic Hydrocarbon Fuel when It Cools a High Temperature Channel

A Set of Vapor-Flow Calorimeter and the Heat Capacities of Benzene and Benzene-Cyclohexane

Endothermic Reaction of High Heat Sink Hydrocarbon Jet Fuel