Abstract:In this paper, a novel two-stage hydrocarbon fuel heating and delivery system was used to more accurately simulate the state of fuel in the cooling channel of the regenerative cooling engine. Different cracking degrees (9-23%) experiments of JP-10 were conducted by using the new heating system, and cracked products were sampled and analyzed. The ignition delay time of high cracking degree product is shorter than that of low cracking degree product. The laminar flame speed of JP-10 and low cracking degree products are similar, the laminar flame speed of high cracking degree products is 32% faster than that of JP-10 when the equivalence ratio is 1.0, and the laminar flame speed of surrogate gas fuel is two times faster than that of JP-10. The supersonic combustion experiments of JP-10 with different cracking degrees and equivalence ratios were also employed at Mach number 3.0 of the isolator entrance, with total temperature-1550 K, total pressure-1.5 MPa, as well as at Mach number 2.5 of the isolator entrance, with total temperature-1250 K, total pressure-0.78 MPa, respectively. The static pressure along the axis of combustor was measured, while the velocity and temperature of the airflow at the exit of combustor were also measured by the tunable diode laser absorption spectroscopy (TDLAS). The distributions of airflow velocity, total temperature and static temperature along the combustor with different conditions were analyzed through a one-dimensional analysis method. The deviations of velocity and temperature of the airflow are less than-4% and-5% for Mach number 3.0, and less than 9% and 4% for Mach number 2.5, which indicates the calculations are in accordance with the TDLAS detections to some extent at Mach 3.0. Specially, supersonic combustion of JP-10 with different cracking degree at the same fuel tem-perature and equivalence ratio were obtained, which benefits studying the influence of different cracking degrees fuel on supersonic combustion characteristics. Furthermore, the experimental data will be helpful for validating the simulation of supersonic combustion.

Thermal Cracking and Heat Sink Measurement of Model Compounds of Endothermic Hydrocarbon Fuels under Supercritical Conditions

MEASUREMENT OF HEAT SINK FOR ENDOTHERMIC FUELS

Numerical Model Development and Validation for Hydrocarbon Fuel Supercritical Heat Transfer with Endothermic Pyrolysis

Coking of Model Hydrocarbon Fuels under Supercritical Condition

Experiment and Modeling on Thermal Cracking of N-Dodecane at Supercritical Pressure

Heat Transfer and Thermal Cracking Behavior of Hydrocarbon Fuel

Thermal Cracking and Heat Transfer of Hydrocarbon Fuels at Supercritical Pressures in Vertical Tubes

Measurements of Coefficient of Convective Heat Transfer for Endothermic Hydrocarbon Fuel Up to Supercritical Pressures

Numerical Investigations on the Molecular Reaction Model for Thermal Cracking of n-Decane at Supercritical Pressures.

Energy Conversion Characteristics and Modeling of Supercritical Hydrocarbon Fuel in Regenerative Cooling

Model Validation and Parametric Study of Fluid Flows and Heat Transfer of Aviation Kerosene with Endothermic Pyrolysis at Supercritical Pressure

Modeling and Simulation of Supercritical-Pressure Turbulent Heat Transfer of Aviation Kerosene with Detailed Pyrolytic Chemical Reactions

Thermal cracking of JP-10 under pressure

Numerical Study on Turbulent Convective Heat Transfer with n-heptane Under Supercritical Pressures

Numerical Study of Fluid Flows and Heat Transfer of Aviation Kerosene with Consideration of Fuel Pyrolysis and Surface Coking at Supercritical Pressures

An Experimental Investigation of Supersonic Combustion of Cracked JP-10

Heat Management in Supersonic/Hypersonic Vehicles Using Endothermic Fuel: Perspective and Challenges

Endothermic Reaction of High Heat Sink Hydrocarbon Jet Fuel

Heat Transfer and Cracking Performance of Endothermic Hydrocarbon Fuel when It Cools a High Temperature Channel

Experimental and Modeling Investigation of N-Decane Pyrolysis at Supercritical Pressures

A Numerical Study of Supercritical Forced Convective Heat Transfer of N-Heptane Inside A Horizontal Miniature Tube