Abstract:This study was designed to develop and characterize a silica-coating method for crystalline nonsilicate ceramic nanoparticles (Al2O3, TiO2, and ZrO2). The hypothesis was that the coated nonsilicate nanoparticles would stably reinforce a polymeric matrix due to effective silanation. Silica coating was applied via a sol-gel method, with tetraethyl orthosilicate as a silica precursor, followed by heat treatment. The chemical and microstructural characteristics of the nanopowders were evaluated before and after silica coating through x-ray diffraction, BET (Brunauer-Emmett-Teller), energy-dispersive x-ray spectroscopy, field emission scanning electron microscopy, and transmission electron microscopy analyses. Coated and noncoated nanoparticles were silanated before preparation of hybrid composites, which contained glass microparticles in addition to the nanoparticles. The composites were mechanically tested in 4-point bending mode after aging (10,000 thermal cycles). Results of all chemical and microstructural analyses confirmed the successful obtaining of silica-coated nanoparticles. Two distinct aspects were observed depending on the type of nanoparticle tested: 1) formation of a silica shell on the surface of the particles and 2) nanoparticle clusters embedded into a silica matrix. The aged hybrid composites formulated with the coated nanoparticles showed improved flexural strength (10% to 30% higher) and work of fracture (35% to 40% higher) as compared with composites formulated with noncoated nanoparticles. The tested hypothesis was confirmed: silanated silica-coated nonsilicate nanoparticles yielded stable reinforcement of dimethacrylate polymeric matrix due to effective silanation. The silica-coating method presented here is a versatile and promising novel strategy for the use of crystalline nonsilicate ceramics as a reinforcing phase of polymeric composite biomaterials.

Sol gel coating of nano-zircoia based ceramics on Fe-Cr-Al alloy fiber media for catalytic applications

Sol Gel Alumina Coating on Fe–Cr–Al–Y Fibre Media for Catalytic Converters

Preparation and Catalytic Properties of ZSM-5 Zeolite Films on FeCrAl Alloy Grids

Inhibition of Metastable Alumina Formation on Fe–Cr–Al–Y Alloy Fibers at High Temperature Using Titania Coating

Preparation of Metallic Monolithic Pt/FeCrAl Fiber Catalyst by Suspension Spraying for VOCs Combustion.

Oxidation Protection of Carbon Fiber by Sol-Gel Derived Boron Doped Yttria Stabilized Zirconia Coatings

Deposit of ZrO2 Coatings on SiC Fibers by Sol-gel Method

Fischer-tropsch synthesis: Catalytic performance of zirconia modified Co/Al2O3

Preparation and Characterization of Sol–gel Derived Zirconia Coated Carbon Fiber

Influence of coating solutions on properties ofγ-Al2O3 washcoat over FeCrAl substrate

Fabrication and Characterization of Ceramic Coatings with Alumina–silica Sol-Incorporated Α-Alumina Powder Coated on Woven Quartz Fiber Fabrics

Studies on the Structure and Catalytic Property of High Surface Area Zirconia Supported Cobalt Fischer-Tropsch Synthesis Catalysts

Novel Cobalt Carbide Catalyst Wall-Coating Method for FeCrAlloy Microchannels Exemplified on Direct Production of Lower Olefins from Syngas

Silica Coating of Nonsilicate Nanoparticles for Resin-Based Composite Materials

Catalytic Cracking of Endothermic Fuels over Meso-HZSM-5/MCM-41 Coatings

Synthesis and Properties of a Precursor Derived Nano Zr(C, N)-carbon Composite Coating on SiC Fibers

Preparation and Characterization of Aluminide/zirconia Composite Coatings by a Three-Step Combined Process

Nanosized (zr, Hf)O2 Coating Reinforced by AlN Whiskers for the Ablation Protection of SiC Coated C/C Composites

Synthesis and characterization of sol-gel derived continuous spinning alumina based fibers with silica nano-powders

Fischer-Tropsch Synthesis: Catalytic Performance Of Zirconia Modified Cobalt/Alumina.

Nano-Zirconia/Mullite Composite Ceramics Prepared By In-Situ Controlled Crystallization From The Si-Al-Zr-O Amorphous Bulk