Abstract:The effect of applying a negative bias during deposition of a previously designed multilayer solar selective absorber coating was studied on two types of substrates (316L stainless steel and Inconel 625). The solar selective coating is composed of different chromium aluminum nitride layers deposited using a combination of radiofrequency (RF), direct current (DC), and high-power impulse magnetron sputtering (HiPIMS) technologies. The chemical composition is varied to generate an infrared reflective/absorber layer (with low Al addition and N vacancies) and two CrAlN intermediate layers with medium and high aluminum content (Al/Cr = 0.6 and 1.2). A top aluminum oxide layer (Al2O3) is deposited as an antireflective layer. In this work, a simultaneous DC-pulsed bias (-100 V, 250 kHz) was applied to the substrates in order to increase the film density. The optical performance, thermal stability, and oxidation resistance was evaluated and compared with the performance obtained with similar unbiased coating and a commercial Pyromark paint reference at 600, 700, and 800 °C. The coating remained stable after 200 h of annealing at 600 °C, with solar absorptance (α) values of 93% and 92% for samples deposited on stainless steel and Inconel, respectively, and a thermal emittance ε25°C of 18%. The introduction of additional ion bombardment during film growth through bias assistance resulted in increased durability, thermal stability, and working temperature limits compared with unbiased coatings. The solar-to-mechanical energy conversion efficiency at 800 °C was found to be up to 2 times higher than Pyromark at C = 100 and comparable at C = 1000.

NiCrAlO/Al2O3 Solar Selective Coating Prepared by Direct Current Magnetron Sputtering and Water Boiling

Optical and Wetting Properties of CuAlO2 Films Prepared by Radio Frequency Magnetron Sputtering

Structure and Thermal Stability of Spectrally Selective Absorber Based on Alcron Coating for Solar-Thermal Conversion Applications

A Single Layer of Chromium Oxide Nanoparticles Films Coated with Carbon by Applying Exploding Wire Technique for Efficient Solar Selective Absorber

Synthesis and Characterization of Multilayered CrAlN/Al2O3 Tandem Coating Using HiPIMS for Solar Selective Applications at High Temperature

Cr-(CrN/TiAlN)m-AlSiN-AlSiO open-air stable solar selective coating for concentrated solar thermal power applications

Microstructure and Thermal Stability of Cu/TixSiyN/AlSiN Solar Selective Absorbing Coating

Design, synthesis and thermal stability study on graded TiN O solar selective absorbing coating fabricated by pulsed DC reactive magnetron sputtering

Optical, Structural and Thermal Characteristics of Cu–CuAl2O4 Hybrids Deposited in Anodic Aluminum Oxide As Selective Solar Absorber

A Novel Design For High-Temperature Solar Selective Coating

Preparation of Al-Cr-Fe Coatings by Heat Treatment of Electrodeposited Cr/Al Composite Coatings

Fabrication, microstructures and optical reflectivity of TiAlN/NiCr composite coating

Double-layer solar absorber coating based on high entropy ceramic AlCrMoTaTiN: Structure, optical properties and failure mechanism

Microstructure, Optical and Electrical Properties of Craln Film As A Novel Material for High Temperature Solar Selective Absorber Applications

Further investigation of a novel high entropy alloy MoNbHfZrTi based solar absorber coating with double antireflective layers

Study of the Mechanical Properties and Thermal Control Performance of Plasma-Sprayed Alumina Coating on Aluminum Alloy Surface

Single cathode sputtered selective solar absorbing surfaces

Lowered infrared emittance and enhanced thermal stability of solar selective absorption properties of anodic aluminum oxide photonic crystal coatings

Sputtered Aluminium Composite Selective Absorbing Surfaces

Electrodeposition of nano-Cu, Ni and binary Ni/Cu into nano-porous AAO layer for high-efficiency black spectrally selective coating

High-temperature thermal stable solar selective absorbing coating based on the dielectric-metal-dielectric structure