Abstract:Purpose The purpose of this paper is to enhance the efficiency of the LED by introducing three-step magnesium (Mg) doping profile. Attention was paid to the effects of the Mg doping concentration of the first p-GaN layer (i.e. layer close to the active region). Attention was paid to the effects of the Mg doping concentration of the first p-GaN layer (i.e. layer close to the active region). Design/methodology/approach Indium gallium nitride (InGaN)–based light-emitting diode (LED) was grown on a 4-inch c-plane patterned sapphire substrate using metal organic chemical vapor deposition. The Cp 2 Mg flow rates for the second and third p-GaN layers were set at 50 sccm and 325 sccm, respectively. For the first p-GaN layer, the Cp 2 Mg flow rate varied from 150 sccm to 300 sccm to achieve different Mg dopant concentrations. Findings The full width at half maximum (FWHM) for the GaN (102) plane increases with increasing Cp 2 Mg flow rate. FWHM for the sample with 150, 250 and 300 sccm Cp 2 Mg flow rates was 233 arcsec, 236 arcsec and 245 arcsec, respectively. This result indicates that the edge and mixed dislocations in the p-GaN layer were increased with increasing Cp 2 Mg flow rate. Atomic force microscopy (AFM) results reveal that the sample grown with 300 sccm exhibits the highest surface roughness, followed by 150 sccm and 250 sccm. The surface roughness of these samples is 2.40 nm, 2.12 nm and 2.08 nm, respectively. Simultaneously, the photoluminescence (PL) spectrum of the 250 sccm sample shows the highest band edge intensity over the yellow band ratio compared to that of other samples. The light output power measurements found that the sample with 250 sccm exhibits high output power because of sufficient hole injection toward the active region. Originality/value Through this study, the three steps of the Mg profile on the p-GaN layer were proposed to show high-efficiency InGaN-based LED. The optimal Mg concentration was studied on the first p-GaN layer (i.e. layer close to active region) to improve the LED performance by varying the Cp 2 Mg flow rate. This finding was in line with the result of PL and AFM results when the samples with 250 sccm have the highest Mg acceptor and good surface quality of the p-GaN layer. It can be deduced that the first p-GaN layer doping has a significant effect on the crystalline quality, surface roughness and light emission properties of the LED epi structure.

Effects of Ⅴ/Ⅲ Ratio and Cp2Mg Flow Rate on Characteristics of Non-Polar A-Plane Mg-delta-doped P-Algan Epi-Layer

Effects of V/III ratio and Cp2Mg flow rate on characteristics of non-polar a-plane Mg-delta-doped p-AlGaN epi-layer

Effects of Cp 2 Mg molar flow rate on structural, optical, and electrical properties of semipolar Mg-doped p-AlGaN epi-layers

Study of electrical and structural properties of non-polar a-plane p-AlGaN epi-layers with various Al compositions

Effects of Mg-doping Temperature on the Structural and Electrical Properties of Nonpolar A-Plane P-Type GaN Films

Influence of High Mg Doping on the Microstructural and Opto-Electrical Properties of AlGaN Alloys

Influence of Mg source flowrate on the properties of isoelectronic in-doping p-AlGaN materials

Study on Mg-doped AlGaN Films Grown by Metal Organic Chemical Vapor Deposition

Enhanced p-type conduction in AlGaN grown by metal-source flow-rate modulation epitaxy

Properties of Si-doped a-plane AlGaN layers

Thickness and Mg doping of graded AlGaN layers: Influence on contact layer's structural and electrical properties for DUV emitters

Optimization and Analysis of Magnesium Doping in MOCVD Grown p-GaN

Doping Characteristics of Mg in InGaAlP and GaP

Properties of Mg-Doped AlGaN Films

Improvement of P-Type Conductivity in Al-rich AlGaN Substituted by MgGa Δ-Doping (aln)m/(gan)n (m≥n) Superlattice

Effects of three-step magnesium doping in p-GaN layer on the properties of InGaN-based light-emitting diode

MOCVD growth and annealing characteristics of Mg-doped AlGaN films

Mg acceptors activation mechanism and hole transport characteristics in highly Mg-doped AlGaN alloys

Doping and compensation in heavily Mg doped Al-rich AlGaN films

The Effect of Periodic Duty Cyclings in Metal-Modulated Epitaxy on GaN:Mg Film

Investigation Of Mg Doping In High-Al Content P-Type Alxga1-Xn (0.3 < X < 0.5)