Abstract:Silica nanoparticles are widely utilized abrasives in chemical mechanical polishing (CMP), and the modification of abrasives and the incorporation of chemical additives represent primary strategies for enhancing CMP performance. In this study, we achieved a modification of the electrical properties of the colloidal silica surface by forming a coating film through the "grafting" of 3-aminopropyltriethoxysilane (APTES) onto the colloidal silica surface. This modification resulted in an augmented mechanical interaction between the abrasive and the wafer during the CMP process, leading to an enhanced material removal rate (MRR) of SiO 2 . However, the post-CMP surface exhibited a relatively higher occurrence of surface defects. Subsequently, cetyltrimethylammonium bromide (CTAB) was added as an auxiliary additive, which promoted the formation of a "special electrostatic self-assembly structure" on the surface of the abrasive, further elevating the SiO 2 MRR. Moreover, CTAB demonstrated the capability to adsorb onto the wafer surface, creating a protective effect that resulted in reduced surface roughness and a decrease in surface defects following CMP. Furthermore, comprehensive characterization of the modified abrasive was conducted using techniques such as transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The mechanisms underlying the improvement in CMP performance were systematically analyzed through experimental phenomena and X-ray photoelectron spectroscopy (XPS), and revealing that the introduction of CTAB indirectly facilitated the adsorption of APTES onto the surface of the colloidal silica. Our study provides a method for the advanced process of SiO 2 CMP with stringent metal ion requirements.

Investigation of the Chemical Residuals on the Fused Silica During Chemical Mechanical Polishing

Application of surface analysis in study on removal mechanism and abrasive selection during fused silica chemical mechanical polishing

Characteristics of Slurry Recycling in Chemical Mechanical Polishing (CMP) of Fused Silica (FS)

XPS, UV–vis Spectroscopy and AFM Studies on Removal Mechanisms of Si-face SiC Wafer Chemical Mechanical Polishing (CMP)

Investigation on morphology and chemistry of the Beilby layer on polished fused silica

The Cycle Characteristics of Slurries in Chemical Mechanical Polishing (CMP) of Fused Silica

Achieving Ultralow Surface Roughness and High Material Removal Rate in Fused Silica Via a Novel Acid SiO2 Slurry and Its Chemical-Mechanical Polishing Mechanism

The Deterioration Characteristics and Mechanism of Polishing Pads in Chemical Mechanical Polishing of Fused Silica

Trivalent lanthanum and ytterbium doped meso-silica/ceria abrasive systems toward chemical mechanical polishing (CMP) and ultraviolet irradiation-assisted photochemical mechanical polishing (PCMP)

Novel green chemical mechanical polishing of fused silica through designing synergistic CeO 2 /h-BN abrasives with lubricity

Effect of colloidal silica particles on subsurface damage of fused silica optics during CMP process

Preparation of Ordered Mesoporous Si02/Mc N anocomposite Abrasives and Their Chemical Polishing Behavior on Fused Silicon Substrates

Development of core–shell SiO 2 @A-TiO 2 abrasives and novel photocatalytic chemical machinal polishing for atomic surface of fused silica

Influence of Colloidal Silica Dispersion on the Decrease of Roughness in Silicon Chemical Mechanical Polishing

Research on Surface Topography of Silicon Wafer in Chemical-mechanical Polishing

Investigation of the chemical action mechanism based on reactive force field in SiC chemical–mechanical polishing process

A special electrostatic self-assembly structure of colloidal silica: Improving Chemical Mechanical Polishing performance

Enhancing Ceria Slurry Performance for Shallow Trench Isolation Chemical Mechanical Polishing Through Non-Ionic Surfactant Addition

Particles Manipulation to Improve Removal Efficiency of Fused Silica in Chemical Mechanical Polishing

Preparation of Silane Modified Sio2 Abrasive Particles and Their Chemical Mechanical Polishing (cmp) Performances

Preparation of alumina/silica core-shell abrasives and their CMP behavior