Abstract:In the present work, an ultrahigh strength 300 M steel was treated by the surface plastic deformation with surface cryogenic grinding treatment (SCGT) technique. The SCGT was carried out by rotational grinding wheel embedded with numerous zirconium corundum abrasive grits, which contributes to a decreasing distribution of strain, strain rate and strain gradient from the treated surface to the matrix. The depth-dependent microstructural evolution was systematically evaluated from micrometer to nanoscale and in particular, the deformation mechanisms and texture alternation were addressed. It was identified that the microstructural evolution starts from the formation of dislocation structures, that is subsequently followed by the distorted microstructures featured as the origination and evolution of ultrafine laminates and ultrafine grains in the form of dislocation activities. Nanocrystalline was generated in the topmost surface region and nanoparticle precipitates induced by the SCGT process occur within a few microns of the treated surface. In SCGT, a very high strain rate of over 10(6) s(-1) and a strain gradient of over 0.2 mu m(- 1) were induced on the topmost surface of 300 M steel sample, which impels the martensite-matrix lamella extended into the elongated structure and finally transformed into the nanosized grains during processing. A dislocation slip-dominated process that was supplemented by the mechanical twinning governs the microstructural evolution pattern during the SCGT process, the nucleus of dynamic recrystallization initiated from the pre-existing dislocation cells were observed, and the transformation from martensite to austenite was effectively suppressed. The increase of grain size from nanoscale to submicron and finally microscale contributes to a decrease of microhardness by 25.6% (from 7.8 GPa at the treated surface to 5.8 GPa at a depth of over 100 mu m from the processed surface).

Grain Refinement in Surficial Cryogenic Grinding

Effect of cryogenic impact deformation and subsequent annealing on microstructure and microhardness of pure copper

Simultaneous Grain Growth and Grain Refinement in Bulk Ultrafine-Grained Copper under Tensile Deformation at Room Temperature

Grain Refinement Mechanism at High Undercooling of Ni80Cu20 Alloy

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Rapid Stress-Driven Grain Coarsening in Nanocrystalline Cu at Ambient and Cryogenic Temperatures

On the microstructural evolution pattern of 300 M steel subjected to surface cryogenic grinding treatment

Nanocrystalline Grain Structures Developed in Commercial Purity Cu by Low-Temperature Cold Rolling

Dynamic Processes for Nanostructure Development in Cu after Severe Cryogenic Rolling Deformation

Grain Refinement and Texture Evolution During High Precision Machining of A Ni-Based Superalloy

Microstructure, microtexture and precipitation in the ultrafine-grained surface layer of an Al-Zn-Mg-Cu alloy processed by sliding friction treatment

Preparation of Ultrafine-Grained Copper Alloy by Annealing Treatment after Multi-Directional Compression

Plastic strain-induced grain refinement at the nanometer scale in copper

Grain Coarsening Behavior in a Nanocrystalline Copper Subjected to Sliding Friction

Experimental study of grain refinement mechanism in undercooled Ni-15at.%Cu alloy

Recrystallization mechanism of grain refinement in hypercooled single phase alloys

Insight into Ultra-Refined Grains of Aluminum Matrix Composites Via Deformation-Driven Metallurgy

Grain Refinement Mechanism under High Strain-Rate Deformation in Machined Surface During High Speed Machining Ti6Al4V

Grain Refinement by Authigenic Inoculation Inherited from the Medium-Range Order Structure of Ni-Cr-W Superalloy

Grain Refinement in Highly Undercooled Solidification of Ni85Cu15 Alloy Melt: Direct Evidence for Recrystallization Mechanism

Effects of Precipitates Versus Solute Atoms on the Deformation-Induced Grain Refinement in an Al–Cu–Mg Alloy