Abstract:Nanosized copper oxide-zirconia particles containing 10-30 mol% of copper were prepared by using a precipitation technique in aqueous tetramethylammonium hydroxide solutions. Two methods, in situ (INS) and step-by-step (SBS), which differed in the time when the copper salt was introduced to the synthesis procedure, were used, and this allowed a comparison of the properties of the final powders produced using the two modes of preparation. The surface areas and phase compositions were different for the samples prepared from the two different methods after calcination at 500 degreesC. A surface area of 168 m(2) g(-1) was obtained for the sample prepared with the SBS method and 121 m(2) g(-1) for the INS method, both contain 30 mol% copper. Tetragonal ZrO2 was observed from X-ray diffraction patterns for all samples prepared with the SBS method, however, no separate phase of copper or copper oxide was observed. It is proposed that all of the copper is finely distributed on the surface of the ZrO2 particles with the SBS method. For the samples prepared from the INS method, tetragonal ZrO2 was obtained at a low copper content and the peaks indexed to tetragonal ZrO2 shifted to higher angle with the increase of copper content, indicating copper ions being incorporated into the lattice. An amorphous compound was obtained at high copper content (30 mol%). The phase change with the calcination temperature was also investigated for the INS sample containing 30 mol% copper. The studies show that tetragonal ZrO2 and copper oxide were present after calcination at 400 degreesC, and tetragonal ZrO2 with a small amount of monoclinic ZrO2, as well as copper oxide, formed after calcination at 700 degreesC. However, after heating at 500 degreesC, amorphous compounds were obtained, suggesting that 500 degreesC could be a phase transition point. The incorporation of copper in the ZrO2 lattice resulted in a loss of order in the ZrO2 structure when calcined at 500 degreesC, with a further increase in the calcination temperature leading to the phase change.

Particle Size and Purity Control Study on ZrW2O8 Powders Using Coprecipitation Method

Synthesis of PbZrO3 Powder by a COprecipitation Method

Synthesis, Characterization and Application of Submicron ZrSiO4 Powder Via Sol-Gel-microemulsion-hydrothermal Method

Preparation and characterization of nano-scale Y2O3-ZrO2 powder by heterogeneous precipitation

Synthesis of Pb(Zr0.52Ti0.48)O3(PZT) Powder by A Partial Lead Oxalate Coprecipitation Method

Co-precipitation of nano Mg–Y/ZrO2 ternary oxide eutectic system: Effects of calcination temperature

Investigation on the Preparation and Properties of Monodispersed Al2O3ZrO2 Nanopowder Via Co-precipitation Method

Pva Assisted Synthesis of Nanosized Perovskite Pzt Powder by A Two-Stage Precipitation Route

Study on Preparation of Yttrium Oxide with Large Particle Sizes and Spherical Shapes by Precipitation with Ammonium Bicarbonate

The Effect of the Preparation Methods on the Structure of Wo3/Zro7

Preparation of Y2O3 doped BaZrO3 powder by coprecipitation

Study on the process and properties of nano-sized polycrystal zirconia powders by co-precipitation in super-alkaline medium

Preparation of Cu Coated ZrW<sub>2</sub>O<sub>8</sub> Composite Powders Via Heterogeneous Precipitation Process

Preparation and characterization of CuO–ZrO2 nanopowders

Coprecipitation Synthesis of MgO-Doped ZrO<sub>2</sub> Nano Powder

Facile Synthesis and Characterization of ZrO₂ Nanoparticles via Modified Co-Precipitation Method

Microstructural Characterization and Crystallization of ZrO2–Y2O3–CuO Solid Solution Powders

Preparations and Characterizations of New Mesoporous ZrO2 and Y2O3-stabilized ZrO2 Spherical Powders

Effect of Calcination Temperature on the Microstructure, Composition and Properties of Agglomerated Nanometer CeO2-Y2O3-ZrO2 Powders for Plasma Spray-Physical Vapor Deposition (PS-PVD) and Coatings Thereof

Synthesis of 3Y–ZrO2 nano-powders via a W/O emulsion

Effect of Al2O3 addition on ZrO2 phase composition in the Al2O3–ZrO2 system