Abstract:Employing HNO3, NH3· H2O, NH4NO3, H2C2O4 and commercial available Y2O3 as starting materials, and using SDBS as surfactant and PEG 2000 as assistant , the precursor Y ( NH4 ) ( C2 O4 ) 2· H2 O and its final products Y 2 O3 powders were successfully fabricated by the improved oxalate precipitation method and subsequent calcination treatment .In this specific route , a little amount of designed Y(NO3)3 solution was added into a certain huge volume of NH 3· H2O-NH4NO3 mixed solution to create Y(OH)3 hydro-gel, so the pH value could be precisely controlled during the process .Then the precursor precipitate was produced by dropping the saturated oxalate acid solution into the obtained white colloidal at 85 ℃.At last, following heat treatment at 950 ℃ for 2 h, the final product Y2 O3 powders were obtained .X-ray powder diffraction ( XRD) and scanning electron microscopy ( SEM) results revealed that the pre-cursor Y(NH4)(C2O4)2· H2O in forms of cubic crystal aggregations was obtained .Despite substantial removal of oxide, carbon and hydrogen ions , the precursor calcined Y 2 O3 particles maintained well morphology properties of the precursor even after calcination at 950 ℃for 2 h.Further, to understand the factors influencing the size and morphology of the final Y 2 O3 particles, experiments were carried out by mainly changing the mass ratio of SDBS/PEG2000 and the pH value in the oxalate acid precipitation process .It was ob-served from the SEM results that the size and shape of the synthesized Y 2 O3 particles could be controlled by precisely adjusting reaction conditions, especially the pH value in the oxalate acid precipitation process .Y2 O3 particles with diameter under 1μm could be made when the pH value in the oxalate acid precipitation process was reduced to 1.8.In addition, based on the thermogravimetric (TG) and differential scanning calorimetry ( DSC) analysis, the thermal decomposition mechanism of precursor was proposed as follows: Y (NH4)(C2O4)2· H2O→Y(NH4)(C2O4)2→Y2O2CO3→Y2O3.

Study on Preparation of Yttrium Oxide with Large Particle Sizes and Spherical Shapes by Precipitation with Ammonium Bicarbonate

Preparation of ultra-fine yttrium oxide by ultrasonic-quenching-homogeneous precipitation method

Preparation of nano-sized Y_2O_3 by ammonium oxalate precipitation method

Controlled Synthesis Of Large Yttria Particles Based On Yttrium Carbonate Crystallization

Preparation And Characterization Of Nano-Yb2o3/Tio2 Particles

Preparation and characterization of nano-scale Y2O3-ZrO2 powder by heterogeneous precipitation

Influence of the Synthesis Conditions on Preparation of Yttria Powders by Urea Precipitation Method

Preparation of large particle rare earth oxides by precipitation with oxalic acid

Preparation and Spherical Morphology Control of Γ-La_2s_3 Powders by Homogeneous Precipitation

Synthesis of Cerium Oxide Polishing Powder by Ammonium Bicarbonate Precipitation

Study on Preparation of Large Particle CeO2 by Precipitation with NH4HCO3

Preparation of Ultrafine Yttria by Wet-Solid-Phase Mechanochemical Reaction

Preparation of Y2O3 nanoparticles and transparent ceramics by homogeneous pecipitation method

Precipitation Synthesis and Sintering of Yttria Nanopowders

Synthesis of Y2O3 nanopowders and transparent Y2O3 ceramics by carbonate-precipitation process

Preparation of Nanoscale Ytterbia by Wet Chemical Methods

Study on preparation of micrometer ceria used ammonium bicarbonate-ammonium hydroxide-oxalic acid by co-precipitation method

The Composition And Crystalline Phase Type Of Products Obtained By Precipitating Yttrium Ion With Ammonium Bicarbonate

Orthogonal Experimental Optimization for Preparation Ofyag Nano-Powders by Co-Precipitation Method

Influences of Preparation Conditions on the Ytterbium-Doped Tin Oxide Nano-Powders

Size-and Shape-Controlled Synthesis and Formation Mechanism of Y(NH4)(C2O4)2·H2O and Y2O3 Phases