Abstract:Distinct from the conventional double‐balanced mixer topology, a resonator was employed at the emitter of the transconductance stage, which enables the utilization of transconductance stage as an active balun, allowing for direct feeding of the single‐ended input without sacrificing the advantageous of the double‐balanced topology. The integration of the resonator reduces the amplitude and phase errors within the active balun segment, thereby enhancing port‐to‐port isolation. The area occupied by the resonator is approximately 1.7 times smaller than that of an RF transformer balun typically employed in conventional double‐balanced topologies. This paper introduces a downconverter mixer employing a modified double‐balanced Gilbert‐cell topology, designed using IHP's 0.13‐μ m SiGe BiCMOS technology. Distinct from the conventional topology, a resonator was employed at the emitter of the transconductance stage, which enables the utilization of transconductance stage as an active balun, allowing for direct feeding of the single‐ended input without sacrificing the advantageous of the double‐balanced topology. The integration of the resonator reduces the amplitude and phase errors within the active balun segment, thereby enhancing port‐to‐port isolation. The area occupied by the resonator is approximately 1.7 times smaller than that of an RF transformer balun typically employed in conventional double‐balanced topologies. The LO and IF differential signals are converted to single‐ended ones through transformer baluns for measurement purposes. The frequencies of operation for RF, LO, and IF are 24–30, 18–24, and 6 GHz, respectively. The conversion loss is 7.7 dB at 26 GHz, with port‐to‐port isolations exceeding 35 dB. The input 1‐dB compression point is 5.7 dBm, while the circuit consumes 65‐mW power from a 3.3‐V voltage supply. Excluding the pads, the active area of the design spans 1 mm2.

High-Linearity Double-Balanced Up-Conversion Mixer with an Active Balun Based on InGaP/GaAs HBT Technique

A 27 - 57 GHz Down-conversion Mixer with Bulk Injection Technique

A group-selected and gain controllable CMOS active mixer for UWB applications

Compact CMOS Baluns for the 4–10 GHz Band Applications

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A Gm-boosted and current peaking wideband merged LNA and mixer

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

An Ultra-Low Power K band Balanced Frequency Doubler with a Novel Current-reused Structure

A High-Efficiency K-band MMIC Linear Amplifier Using Diode Compensation

High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

A UWB Mixer with a Balanced Wide Band Active Balun Using Crossing Centertaped Inductor

A high gain, wide band (2–10 GHz), and low noise active balun merged folded mixer for the full-band UWB application

A 24‐ghz Active Up/down Bidirectional Mixer in 130‐nm RF CMOS

A 24-to-30 GHz Ultra-High-Linearity Down-Conversion Mixer for 5G Applications Using a New Linearization Method

A K-Band Active Up/Down Bidirectional Mixer in 130-Nm CMOS

A 24–30‐GHz Modified Gilbert‐Cell Downconverter With High Linearity and Isolation

A High Performance Double-Balanced Gilbert Mixer with Active Loads for 2.4-GHz ISM Band Application

Analysis and Design of a Broadband SiGe HBT Image-Reject Mixer Integrating Quadrature Signal Generator

A 30-60 GHz Broadband Low LO-Drive Down-Conversion Mixer with Active IF Balun in 65 nm CMOS Technology

A 0.13&#x03bc;m CMOS UWB Receiver Front-End Using Passive Mixer

A 0.13-Mu M Cmos 0.1-12 Ghz Active Balun-Lna For Multi-Standard Applications