Abstract:A wideband low-noise amplifier (LNA) featuring transformer-based wideband input matching is proposed for millimeter-wave applications. By analyzing the properties of conventional series input matching networks, which were widely employed in narrowband LNAs and shunt-series matching networks for bandwidth extension, a novel input matching network possessing the merits of both was proposed. For further bandwidth extension, another peak of input impedance at a higher frequency is introduced for the proposed input matching network. Moreover, it is proved that the proposed input matching network can suppress the gate resistor noise, resulting in significant noise figure (NF) improvement of an LNA. On the other hand, the NF is further reduced by connecting a transformer between the two amplification stages, which helps suppress the noise contribution from the second stage, leading to an LNA design with NF lower than 4.5 dB over a very wide operating bandwidth. To enhance the gain bandwidth, the peak distribution, including both shunt peaking and series peaking, is discussed. By appropriately distributing these peaks, which is also known as the pole-tuning technique, a wider gain bandwidth can be obtained. To validate the proposed techniques, an LNA with two common-source (CS) stages is designed and fabricated using a 65-nm CMOS process, and the overall chip size, including all pads, is only 0.26 mm². The two CS stages are cascoded for dc biasing to reduce the power consumption. Experimental results show that a peak gain of 13.5 dB is achieved within a -3-dB bandwidth from 19.2 to 42.6 GHz. The measured NF is 3.1-4.5 dB, and the input 1-dB gain compression point (IP1 dB) ranges from -13.54 to -9.89 dBm in the entire gain bandwidth. The input return loss S₁₁ is less than -10 dB over a frequency range of 16.8-38.9 GHz. Moreover, benefiting from the current-reuse technique, the power consumption of the LNA is only 6.36-mW.

A Gm-boosted and current peaking wideband merged LNA and mixer

Analysis and Design of Ultra-Wideband Low-Noise Amplifier with Input/Output Bandwidth Optimization and Single-Ended/Differential-Input Reconfigurability.

A Compact 2.1–39 GHz Self-Biased Low-Noise Amplifier in 65 Nm CMOS Technology

A 0.061-Mm² 1–11-Ghz Noise-Canceling Low-Noise Amplifier Employing Active Feedforward with Simultaneous Current and Noise Reduction

A 27 - 57 GHz Down-conversion Mixer with Bulk Injection Technique

3-10 GHz self-biased resistive-feedback lna with inductive source degeneration

A 6.5-12 GHz Balanced Variable Gain Low-Noise Amplifier with Frequency-Selective Non-Foster Gain Equalization Technique

A 11.2 Mw 48–62 GHz Low Noise Amplifier in 65 Nm CMOS Technology

0.9–10GHz low noise amplifier with capacitive cross coupling

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A 6.512-GHz Balanced Variable-Gain Low-Noise Amplifier With Frequency-Selective Gain Equalization Technique

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

A V-Band Compact LNA With G<inf>m</inf>-Boosting and Noise-Cancelling Technique

A 52–73-GHz LNA With Tri-Coupled Transformer for G m Boosting and Enhanced Noise Canceling

A 21-to-41-GHz High-Gain Low Noise Amplifier With Triple-Coupled Technique for Multiband Wireless Applications

A 10ghz 2.8db Gain Passive Mixer In 0.18um Cmos Technology

A 37-to-41.8 GHz Double-Gm-Boosting LNA with 2.9-Db NFmin Using Quadruple-Coupling Transformer for Phased-Array Transceivers.

A Wideband CMOS LNA Using Transformer-Based Input Matching and Pole-Tuning Technique

A Low Power Inductorless Wideband LNA With G m Enhancement and Noise Cancellation

A 0.0081mm2 0.15–5.9-Ghz Low Noise Amplifier with Noise Cancelling and Current Reuse Techniques

Design of a 2–18 GHz low noise amplifier MMIC with current reused topology