Abstract:Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

Digitally Assisted IIP2 Calibration for CMOS Direct-Conversion Receivers

An Effective DC Offset Calibration Method Combined with Analog and Digital Circuits for Direct Conversion Receivers

A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A Highly Linear 2.4GHz Low Noise Amplifier

A 0.1-1.9Ghz 65nm CMOS Variable-Gain Mixer-First Receiver with DSA and Noise-Shaping TIA.

A High-Linearity 7–9-Ghz Receiver Front End with Strength-Oriented Nonlinearity Cancellation

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

Direct conversion receiver with high conversion gain and wide tuning range in 0.18 um CMOS

A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 Μm CMOS Technology

A Low Power Direct Conversion Receiver RF Front-End with High In-Band IIP2/IIP3 and Low 1/f Noise

CMOS High-ⅡP2 Mixer for Direct Conversion Receivers

High linearity 2<sup>nd</sup> IF CMOS mixer for DRM/DAB receiver

A Hybrid Coupler-First 5ghz Noise-Cancelling Dual-Mode Receiver with +10dbm In-Band IIP3 in Current-Mode and 1.7db NF in Voltage-Mode.

A High Linearity Current Mode Second if Cmos Mixer for A Drm/Dab Receiver

Design of Ultra-Low-Power 60-Ghz Direct-Conversion Receivers in 65-Nm CMOS

Analysis and Design of a High-Linearity Receiver RF Front-End with an Improved 25%-Duty-cycle LO Generator for WCDMA/GSM Applications

A 2.4ghz Low Power Highly Linear Mixer For Direct-Conversion Receivers

A Low Noise High Linearity RF Front End Circuits Design