Abstract:Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

Analysis and Design of a High-Linearity Receiver RF Front-End with an Improved 25%-Duty-cycle LO Generator for WCDMA/GSM Applications

A high-linearity receiver RF front-end with a high-performance 25%-duty-cycle LO generator for WCDMA/GSM applications

Design of a High-Linearity RF Front-End with IP2 Calibration for SAW-less WCDMA Receivers.

A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A 0.1-1.9Ghz 65nm CMOS Variable-Gain Mixer-First Receiver with DSA and Noise-Shaping TIA.

A High-Linearity 7–9-Ghz Receiver Front End with Strength-Oriented Nonlinearity Cancellation

28.8 A 21dBm-OP<inf>1dB</inf> 20.3%-Efficiency -131.8dBm/Hz-Noise X-Band Cartesian-Error-Feedback Transmitter with Fully Integrated Power Amplifier in 65nm CMOS

A High-Linearity WCDMA/GSM Reconfigurable Transceiver in 0.13- CMOS

A High Linearity Variable Gain LNA for WCDMA Receiver Front-End

Analysis and Design of a 1.8–2.7 GHz Tunable 8-Band TDD LTE Receiver Front-End

A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 Μm CMOS Technology

A 2.4ghz Low Noise High Linearity RF Front-End Design.

CMOS Highly Linear Direct-Conversion Transmitter for WCDMA with Fine Gain Accuracy

A Highly Linear Lowpass Filter for GSM /WCDMA Receivers

A Dual-Mode Analog Baseband Utilizing Digital-Assisted Calibration for WCDMA/GSM Receivers

A 0.1∼4GHz receiver and 0.1∼6GHz transmitter with reconfigurable 10∼100MHz signal bandwidth in 65nm CMOS

A+21.2 Dbm Out-Of-Band Iip3 0.2-3ghz Rf Front-End Using Impedance Translation Technique

A Multi-Band Low-Noise Transmitter With Digital Carrier Leakage Suppression and Linearity Enhancement

An Interference-Robust Reconfigurable Receiver with Automatic Frequency-Calibrated LNA in 65-Nm CMOS