Abstract:Monte Carlo based GEANT4 simulations have been carried out to estimate the efficiency (<math>η</math>) of thermal neutron detection with boric acid (H3BO3) as a converter material. Different geometries of detector configurations — planar stack, sphere, cylinder and cuboid were considered and their efficiency were computed for relevant geometric parameters along with different 10B enrichment (<math>BE</math>) levels content in boric acid, with Low Level Discriminator (LLD) value fixed at 300 keV. The planar stack configuration detector was designed by replicating two dimensional detector units (DUs) – each consisting of boric acid as a converter material and Silicon (Si) as a detector material – in the third dimension. The simulation carried out for varied layer thicknesses (<math>0.25μm</math> to <math>10μm</math>) of boric acid showed that efficiency (<math>η</math>) increased with increasing thickness, reached a maximum at a critical thickness (<math>tsc</math>) and thereafter found to decrease. Typically, at a critical thickness of <math>∼</math>3.5<math>μm</math>, the <math>η</math> for 100% <math>BE</math> content in boric acid was found to be 15.96% for 30 DUs. For the case of sphere, cylinder and cuboid of boric acid embedded in Si, the simulations were performed for diameter and width both varying from <math>0.5μm</math> to <math>9.5μm</math> in steps of <math>0.5μm</math>. In particular for cylinder and cuboid geometries, the depth was also varied from <math>25μm</math> to <math>275μm</math> with a step size of <math>25μm</math>. In all these configurations <math>η</math> was found to increase initially and was maximum at a critical diameter and width of <math>∼</math>8–9<math>μm</math>, and thereafter it was found to reduce. Apart from the simulated <math>η</math> estimation, histogram plots depicting the energy deposited in Si detector region by the generated charged particles (7Li <math>=</math> 0.839 MeV and <math>α=1.47MeV</math>) upon thermal neutron interaction in boric acid have also been studied for various geometrical parameters such as thickness, diameter and width of detector.

The Research on the Effect of Boron Layer Roughness for the Detection Efficiency of Boronlined Gaseous Neutron Detector

Study of boron-lined straw-tube detector array for neutron scattering measurement

Research of boron lined honey-neutron detector realized with atomic layer deposition

The Research Of High Detection Efficiency Boron Lined Detector With A Honeycomb Neutron Converter

The Research on the Suppression of Spurious Neutrons for A Neutron Detector Array That May Be Used in the Neutron Scattering

Method for stabilizing the detection efficiency of grazing angle incidence boron-lined neutron detectors

Efficiency of Boric acid coated semiconductor neutron detector - A GEANT4 simulation study

Study of uniform drift electric field used for boron-lined honeycomb neutron detector

Research on a Neutron Detector With a Boron-Lined Honeycomb Neutron Converter

Effect of substrate roughness and material selection on the microstructure of sputtering deposited boron carbide thin films

Boron-10 layers, Neutron Reflectometry and Thermal Neutron Gaseous Detectors

Realization of a Thin Boron Layer Neutron Beam Monitor

Study of Boron Coated Straw Detectors for Small Angle Neutron Scattering on Cphs

Boric acid as converter material for semiconductor neutron detector- A GEANT4 simulation study

The Study of Boron-Lined Honeycomb Neutron Detector with a Multi-Wire Proportional Chamber Readout

Application of thin boron deposit by electrophoresis as neutron detectors

Realization and Test of Position Sensitive Boron Coated Straw-Tube

Study Of Delay-Line Readout For Boron Coated Straw Detector

Development and performance evaluation of a multi-layer boron-lined detector for the CPHS-SANS instrument

Comparison of Neutron Detection Performance of Four Thin-Film Semiconductor Neutron Detectors Based on Geant4

Suppression of Spurious Neutrons for the Neutron Detector Used in Small Angle Neutron Scattering