Abstract:Polymeric positive temperature coefficient (PTC) materials with low switching temperature points are crucial for numerous electronic devices, which typically function within the room temperature range (0-40 °C). Ideal polymeric PTC materials for flexible electronic thermal control should possess a room-temperature switching temperature, low room-temperature resistivity, exceptional mechanical flexibility, and adaptive thermal control properties. In this study, a novel PTC material with a room-temperature switching temperature and superb mechanical properties has been designed. A blend of a semi-crystalline polymer EVA with a low melting temperature (Tm) and an amorphous polymer (PVAc) with a low glass transition temperature (Tg) was prepared. Low-cost graphite was chosen as the conductive filler, while CNF was incorporated as a hybrid filler to enhance the material's heating stability. PVAc0.4/EVA0.6/GP-3wt.% CNF exhibited the lowest room temperature resistivity, and its PTC strength (1.1) was comparable to that without CNF addition, with a Curie temperature of 29.4 °C. Room temperature Joule heating tests revealed that PVAc0.4/EVA0.6/GP-3wt.% CNF achieved an equilibrium temperature of approximately 42 °C at 25 V, with a heating power of 3.04 W and a power density of 3.04 W/cm2. The Young's modulus of PVAc0.4/EVA0.6/GP-3wt.% CNF was 9.24 MPa, and the toughness value was 1.68 MJ/m3, indicating that the elasticity and toughness of the composites were enhanced after mixing the fillers, and the mechanical properties of the composites were improved by blending graphite with CNF.

Cold-sintered V2O5-PEDOT:PSS Nanocomposites for Negative Temperature Coefficient Materials

Semiconducting Properties of Cold Sintered V2O5 Ceramics and Co-sintered V2O5-PEDOT:PSS Composites

Cold Sintering Process for a BaTiO3/Poly(vinylidene difluoride) Ceramic-Polymer Composite: Evaluation of the Structural and Microwave Dielectric Properties

Sintering Temperature and Impedance Analysis of Mn0.9co1.2ni0.27mg0.15al0.03fe0.45o4 Ntc Ceramic Prepared by W/O Microemulsion Method

Microstructures and Electrical Properties of V2O5and Carbon-Nanofiber Composites Fabricated by Cold Sintering Process

Preparation and Characterization of Negative Temperature Coefficient (ni,mn) 3 O 4 –la(mn,ni)o 3 Composite

Low-Temperature Sintering of Negative–Positive-Zero-Type Temperature-Stable Ceramics with ZnO–B2O3Flux and SrCO3Additive

Preparation of zinc oxide/poly-ether-ether-ketone (PEEK) composites via the cold sintering process

YCr0.5Mn0.5O3 negative temperature coefficient perovskite ceramics sintered under reducing atmosphere: Microstructure and electrical properties

Preparation of Si 3 N 4 /V 2 O 5 Composite Films for Negative Temperature Coefficient Materials

Low-temperature synthesis of K0.5Na0.5NbO3 ceramics in a wide temperature window via cold-sintering assisted sintering method and enhanced electrical properties

Synthesis and high thermal stability of Mn doped Y2/3Cu3Ti4O12 negative temperature coefficient ceramic

Synthesis of YCrO 3 ceramics through a field-assisted sintering technique

Design for High-Performance Functional Composite Thermistor Materials by Glass/ceramic Composing

Water-Stable Hybrid Lead-Free Perovskite for Negative Temperature Coefficient Thermistors

Pure V2O5 high-electricity transmission properties at low temperatures by structural changes

Microstructure and Electrical Property of NaNbO3 Ceramics Prepared by Cold Sintering Process Assisted Post-Heat-treatment

Vacuum Hot Pressed Highly Dense, Nanograined Mg(Al1−xCrx)2O4 Ceramics

Preparation and Temperature Coefficient of Resistance Characteristics of Nano-VO2/PEDT Composite

Structure and Electrical Performance of Mn1.5−0.5xCo0.9−0.3xNi0.6−0.2xCuxO4 NTC Ceramics Prepared by Heterogeneous Precipitation

Flexible Positive Temperature Coefficient Composites (PVAc/EVA/GP-CNF) with Room Temperature Curie Point