Abstract:For aluminum-based alloy particles, the addition of alloying element lithium (Li) with the properties of a high chemical activity and a low melting/boiling point can significantly improve the thermo-reactive properties of aluminum (Al) particles. To further reveal the combustion mechanism, this paper presents the nitriding reaction and combustion characteristics of Al-Li alloy in nitrogen (N 2 ) through thermogravimetric analysis and differential scanning calorimetry (TG-DSC) analysis at a low heating rate and laser-induced ignition experiments at a high heating rate, considering the influences of two kinds of Li contents (1.0 wt% @ Al-1.0Li and 2.5 wt% @ Al-2.5Li) on these characteristics and making a comparison to the counterpart Al. Al-Li alloy powders as-prepared by gas atomization method showed the texture of the Li-rich eutectic phase compounds on the surface by scanning electron microscope (SEM) characterization. The TG-DSC results demonstrated that the thermal nitriding reaction of Al-Li alloy in N 2 was significantly faster than that of pure Al. The nitriding reaction temperature decreased from 853 °C for pure Al to 245 °C for Al-2.5Li alloy with a reduction of 71 %. The final weight gain of Al-2.5Li alloy was almost three times higher than that of pure Al in N 2 . The SEM photograph of intermediate nitriding products revealed that the cracks and loose "island" structures in the Li-rich zone on the Al-Li surface were the key to preventing the formation of a "passivation effect" into Al and promoting N 2 uptake during melting. In addition, Li also acts as a catalytic carrier and "oxygen absorber" to enhance the Al-N reaction. The combustion of single Al-Li alloy microparticles induced by laser showed two stages: preheating and rapid nitriding. Al-Li alloy particles were ignited more rapidly and showed typical gas-phase / surface combustion modes different from pure Al. According to these findings, the combustion mechanism was proposed to help guide the development of Al-based solid propellants containing Li and the synthesis of AlN/Al composites in nitrogen-rich environments.

Combustion synthesis of fine aluminum nitride powders under micropositive N 2 pressure with water additive

Structural Formation and Mechanism in Combustion Synthesis of Nitrogen Ceramics (AIN, Si<sub>3</sub>N<sub>4</sub> and AIN-SiC)

Synthesis of nearly spherical AlN particles by an in-situ nitriding combustion route

Facile synthesis of monodisperse aluminum nitride microspheres

Combustion synthesis of α-Si3N4 powders using in-situ nano-SiO2 coated Si and Si3N4 reactants

Preheating-assisted Combustion Synthesis of Β-Si3n4 Powders at Low N2 Pressure

Hydrothermal-carbothermal synthesis of highly sinterable AlN nanopowders

Synthesis of aluminum nitride by nitridation of γ-Al 2O3 nanopartlcles in flowing ammonia

Combustion Synthesis of Α-Si3n4 with Green Additives

Combustion Synthesis of AlN–SiC Solid Solution Particles

Synthesis of Ultrafine AlN Powders in an Al-OC-N System

Enhancement effect of Li addition on nitriding reaction and combustion of Al-Li alloy in N 2

Effect of Reaction Atmosphere on Combustion Synthesis of Ti2AlN

Combustion synthesis Si3N4 powders by using activation process

Combustion synthesis of AlN-SIC solid solutions

Microstructure and Thermo‐Kinetics Analysis in Combustion Synthesis of Si3N4 with High α‐Phase Content

Combustion Synthesis of ZrN and AlN Using Si3N4 and BN As Solid Nitrogen Sources

Reaction Model and Mechanism of Preparing (Al2O3 + C) Precursor for Carbothermal Synthesis of AlN by a Modified Low Temperature Combustion Synthesis Method

The study of combustion synthesis of fine-particle γ-lithium aluminate

Synthesis of Aluminum Nitride by Nitridation of Γ-Al2o3 Nanoparticles in Flowing Ammonia

Combustion Synthesis of MgSiN2 Powders and Si3N4‐MgSiN2 Composite Powders: Effects of Processing Parameters