Abstract:For aluminum-based alloy particles, the addition of alloying element lithium (Li) with the properties of a high chemical activity and a low melting/boiling point can significantly improve the thermo-reactive properties of aluminum (Al) particles. To further reveal the combustion mechanism, this paper presents the nitriding reaction and combustion characteristics of Al-Li alloy in nitrogen (N 2 ) through thermogravimetric analysis and differential scanning calorimetry (TG-DSC) analysis at a low heating rate and laser-induced ignition experiments at a high heating rate, considering the influences of two kinds of Li contents (1.0 wt% @ Al-1.0Li and 2.5 wt% @ Al-2.5Li) on these characteristics and making a comparison to the counterpart Al. Al-Li alloy powders as-prepared by gas atomization method showed the texture of the Li-rich eutectic phase compounds on the surface by scanning electron microscope (SEM) characterization. The TG-DSC results demonstrated that the thermal nitriding reaction of Al-Li alloy in N 2 was significantly faster than that of pure Al. The nitriding reaction temperature decreased from 853 °C for pure Al to 245 °C for Al-2.5Li alloy with a reduction of 71 %. The final weight gain of Al-2.5Li alloy was almost three times higher than that of pure Al in N 2 . The SEM photograph of intermediate nitriding products revealed that the cracks and loose "island" structures in the Li-rich zone on the Al-Li surface were the key to preventing the formation of a "passivation effect" into Al and promoting N 2 uptake during melting. In addition, Li also acts as a catalytic carrier and "oxygen absorber" to enhance the Al-N reaction. The combustion of single Al-Li alloy microparticles induced by laser showed two stages: preheating and rapid nitriding. Al-Li alloy particles were ignited more rapidly and showed typical gas-phase / surface combustion modes different from pure Al. According to these findings, the combustion mechanism was proposed to help guide the development of Al-based solid propellants containing Li and the synthesis of AlN/Al composites in nitrogen-rich environments.

Enhancement effect of Li addition on nitriding reaction and combustion of Al-Li alloy in N 2

Laser-Induced Ignition and Combustion of Single Micron-Sized Al-Li Alloy Particles in High Pressure Air/N2

Ignition and combustion of Al–Mg–Li alloy particles at elevated pressures

The Effect of Li-Al Alloy on Combustion Performance of B/PTFE Fuel-Rich Propellant

Improved ignition and combustion performances of aluminum nanoparticles by in-situ partial conversion of native alumina to surface Al-MOF shell

Modifying the ignition, combustion and agglomeration characteristics of composite propellants via Al-Mg alloy additives

Enhancing the combustion of nAl with AlF 3 coating: gas–solid reaction mechanism for reducing combustion agglomeration of Al powder

Effect of Al Content on Reaction Laser Sintering of Ni-Al Powder

Enhancement of the ignition and combustion performance of nano-aluminum: the effect of cryolite

Effect of pressure and oxygen content on the ignition and combustion of Al–Mg alloy

Preparation of high-energy Al-Li alloy powders with enhanced compatibility and combustion performance by dense fluorosilane polymer composite coating

Influence of the Hierarchy Structure of Aluminum Particles on Density, Combustion Efficiency, and Ignition Delay

Improvement of ignition and combustion performance of micro-aluminum particles by double-shell nickel-phosphorus alloy coating

Combustion synthesis of fine aluminum nitride powders under micropositive N 2 pressure with water additive

Study on a novel Al-B-Li alloy powder with high enthalpy of combustion

The study of combustion synthesis of fine-particle γ-lithium aluminate

Selective Coating Fabrication and Combustion Performance of Al-5Li Alloy Particles with High Stability and Compatibility with HTPB

Synthesis of nearly spherical AlN particles by an in-situ nitriding combustion route

Effect of AlN nanoparticle doping on thermophysical properties of nitrate via mechanical milling: Experimental studies and microscopic mechanisms

Effects of NH4Cl on the synthesis of aluminum nitride by the spontaneous combustion of mechanically activated aluminium powder

Promoting Effect of Silicon Particles on Gas-Diffusion-reaction System: In-situ Synthesis of AlN in Al-Si Materials