Abstract:The performance of propellants, explosives and pyrotechnics is known to benefit from the use of metallic alloys as fuel additives. Previous studies have shown that switching from pure Al to Al-Mg alloy can improve the agglomeration and combustion features of composite propellants. However, the optimal ratio of Al and Mg has yet to be explored. We experimentally examine the effects on ignition, combustion and agglomeration arising from substituting pure Al particles with four different Al-Mg alloys whose Mg content ranges from 10 to 60%. Using thermogravimetric−differential scanning calorimetry, we find that switching to Al-Mg alloy can enable oxidation to occur earlier and can increase the oxidation rate and the enthalpy of thermal reaction, which is found to be positively correlated with the Mg content. Using laser ignition measurements, we find that the addition of Mg can promote the ignition and combustion of Al, with (Al/Mg)0.5 exhibiting the most balanced combination of a high combustion intensity, a short ignition delay, and a high mass burning rate. Through high-pressure measurements taken at 1 to 7 MPa, we find that switching to Al-Mg alloy can increase the propellant burning rate (by nearly a factor of two) and the pressure exponent (from 0.23 to 0.43). We also find that the burning rate and pressure exponent are both highest for the propellant containing (Al/Mg)0.1, but that both quantities decrease with further increases in Mg content. High-speed microscopic surface imaging at 1 MPa reveals that increasing the Mg content can increase the overall combustion intensity of the propellant and decrease the diameter of spherical agglomerates, consistent with the observed size distribution of the condensed combustion products. From these measurements, it can be concluded that (Al/Mg)0.5 provides the optimal balance of ignition, combustion and agglomeration characteristics in the formulation of composite propellants containing Al-Mg alloy.

Preparation of high-energy Al-Li alloy powders with enhanced compatibility and combustion performance by dense fluorosilane polymer composite coating

Preparation of core-shell structured Al-5Li@HTPB powders with improved stability and combustion performance by using perfluoroalkylsilane as a surfactant

Selective Coating Fabrication and Combustion Performance of Al-5Li Alloy Particles with High Stability and Compatibility with HTPB

Stabilization Coating of Aluminum-Lithium Alloy and Its Application in Propellant

Comparative Study on Combustion Behavior of Aluminum-Based Alloy Fuels and Aluminum Powder in Solid Propellants

Tuning the agglomeration and combustion characteristics of aluminized propellants via a new functionalized fluoropolymer

Modifying the ignition, combustion and agglomeration characteristics of composite propellants via Al-Mg alloy additives

Polyphenols-inspired interface modification and reduced agglomeration of solid propellants via a functionalized fluorine-containing organic substance coating layer

Laser-Induced Ignition and Combustion of Single Micron-Sized Al-Li Alloy Particles in High Pressure Air/N2

Characterization of an Aluminum–Lithium-Alloy-Based Composite Propellant at Elevated Pressures

Improved Combustion Performance of Solid Propellant with Sliver Nanoparticle Decorated Al Addition

Enhancing the combustion of nAl with AlF 3 coating: gas–solid reaction mechanism for reducing combustion agglomeration of Al powder

In situ preparation of Al@3-Perfluorohexyl-1, 2-epoxypropane@glycidyl azide polymer (Al@PFHP@GAP) high-energy material

Study on Preparation, Application and Modification of Flake Aluminium Powder

Study on a novel Al-B-Li alloy powder with high enthalpy of combustion

Calcium Fluoride Promoting the Combustion of Aluminum Powder

Ignition and combustion of Al–Mg–Li alloy particles at elevated pressures

High-Energy Composite Fuels with Improved Combustion Efficiency by Using AlH 3 Embedded with Al Particles

Ignition and Combustion Characteristics of Aluminum-Based Fluorine-Containing Composite Powder

Preparation and properties of Al flakes and Al/Mg alloy powder

Preparation and characterization of core-shell Al@PFHP with improving the combustion and ignition properties of aluminum powder