Abstract:Adding other metals is an efficient method of breaking through the energy release efficiency limitation of boron-based fuels. A laser ignition testing system was used for investigating the ignition and heterogeneous combustion characteristics of aluminum boride and boron–aluminum blend. The emission spectra and combustion flames of the samples during combustion were recorded by a fiber optic spectrometer and a high-speed camera, respectively. The component, morphology, and distribution features of the condensed combustion products (CCPs) were then analyzed using an X-ray diffractometer, a scanning electron microscope, and an X-ray energy dispersive spectrometer. The emission spectral intensity curves show that the boron–aluminum blend has better ignition feature than aluminum boride (the ignition delay time was 45% shorter). However, the combustion intensity and self-sustaining combustion time of boron–aluminum blend are both inferior to those of aluminum boride. In full wave emission spectra of the samples, the characteristic peaks of combustion intermediate products like BO2, AlO, and AlO2 were found. The combustion flames of the two samples were both yellow green and tapered. The variation trend of the flame size corresponded to that of the emission spectral intensity curves. During the first half of the combustion, large amounts of sparks were ejected from the combustion flame of boron–aluminum blend, which caused the acute fluctuation of combustion intensity. B, Al, B2O3, Al2O3, AlN, and Al5O6N were detected in the CCPs of both samples. In addition, the CCPs of aluminum boride contained unburned AlB2, and those of boron–aluminum blend contained Al4B2O9. Webbed AlN fibers were observed only in the CCPs of boron–aluminum blend, while AlN and Al5O6N whiskers were found in those of both samples. The observed bulks were partially oxidized AlB2 in the CCPs of aluminum boride, or partially oxidized B in those of boron–aluminum blend. As both diffusion and melt-dispersion reactions of aluminum were proceeded during the combustion of boron–aluminum blend, oxidation products of aluminum with different morphology were found in the CCPs of boron–aluminum blend as follows: smooth aluminum spheres with low oxidation degree, rough aluminum oxide spheres with high oxidation degree, empty aluminum oxide shells with hollows or cracks, and fine aluminum oxide particles adhered on the surface of boron bulks.

Study on a novel Al-B-Li alloy powder with high enthalpy of combustion

Combustion and Energy Performance of Multiple Aluminum-Based Alloy Particles

Research on the energy properties and the storage stability of Al–Si–Li ternary alloy powders

Preparation of high-energy Al-Li alloy powders with enhanced compatibility and combustion performance by dense fluorosilane polymer composite coating

Laser-Induced Ignition and Combustion of Single Micron-Sized Al-Li Alloy Particles in High Pressure Air/N2

Comparative Study on Combustion Behavior of Aluminum-Based Alloy Fuels and Aluminum Powder in Solid Propellants

Ignition and combustion of Al–Mg–Li alloy particles at elevated pressures

Preparation of core-shell structured Al-5Li@HTPB powders with improved stability and combustion performance by using perfluoroalkylsilane as a surfactant

Dehydrogenation Performances of Different Al Source Composite Systems of 2libh4 + M (M = Al, LiAlH4, Li3AlH6).

Evaluation of the Combustion Properties and Catalytic Activity of MgAlB Energetic Ternary Particles

Combustion and heat release characteristics of micron aluminum with extremely large specific surface area obtained by L-malic acid surface corrosion

Ignition and heterogeneous combustion of aluminum boride and boron–aluminum blend

Enhancement effect of Li addition on nitriding reaction and combustion of Al-Li alloy in N 2

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Hydrogen Storage Properties of LiBH4–Li3AlH6 Composites

Improved ignition and combustion performances of aluminum nanoparticles by in-situ partial conversion of native alumina to surface Al-MOF shell

Preparation and Characterization of Mg-Al-B Alloy (Mg0.5Al0.5B2) Via High-Temperature Sintering

Modifying the ignition, combustion and agglomeration characteristics of composite propellants via Al-Mg alloy additives

Thermal Oxidation and Heterogeneous Combustion of AlH3 and Al: A Comparative Study

Combustion of aluminum particles in a high-temperature furnace under various O2/CO2/H2O atmospheres

Nanoenergetic Materials: Enhanced Energy Release from Boron by Aluminum Nanoparticle Addition.