Abstract:For aluminum-based alloy particles, the addition of alloying element lithium (Li) with the properties of a high chemical activity and a low melting/boiling point can significantly improve the thermo-reactive properties of aluminum (Al) particles. To further reveal the combustion mechanism, this paper presents the nitriding reaction and combustion characteristics of Al-Li alloy in nitrogen (N 2 ) through thermogravimetric analysis and differential scanning calorimetry (TG-DSC) analysis at a low heating rate and laser-induced ignition experiments at a high heating rate, considering the influences of two kinds of Li contents (1.0 wt% @ Al-1.0Li and 2.5 wt% @ Al-2.5Li) on these characteristics and making a comparison to the counterpart Al. Al-Li alloy powders as-prepared by gas atomization method showed the texture of the Li-rich eutectic phase compounds on the surface by scanning electron microscope (SEM) characterization. The TG-DSC results demonstrated that the thermal nitriding reaction of Al-Li alloy in N 2 was significantly faster than that of pure Al. The nitriding reaction temperature decreased from 853 °C for pure Al to 245 °C for Al-2.5Li alloy with a reduction of 71 %. The final weight gain of Al-2.5Li alloy was almost three times higher than that of pure Al in N 2 . The SEM photograph of intermediate nitriding products revealed that the cracks and loose "island" structures in the Li-rich zone on the Al-Li surface were the key to preventing the formation of a "passivation effect" into Al and promoting N 2 uptake during melting. In addition, Li also acts as a catalytic carrier and "oxygen absorber" to enhance the Al-N reaction. The combustion of single Al-Li alloy microparticles induced by laser showed two stages: preheating and rapid nitriding. Al-Li alloy particles were ignited more rapidly and showed typical gas-phase / surface combustion modes different from pure Al. According to these findings, the combustion mechanism was proposed to help guide the development of Al-based solid propellants containing Li and the synthesis of AlN/Al composites in nitrogen-rich environments.

The study of combustion synthesis of fine-particle γ-lithium aluminate

Self-propagating high-temperature synthesis and reaction mechanism of super-fine particles of gamma-LiAlO2

Self-propagating High-temperature Synthesis and Reaction Mechanism of Super-fine Particles of γ-LiAlO2

A novel combustion process for the synthesis of fine particle α-alumina and related oxide materials

Laser-Induced Ignition and Combustion of Single Micron-Sized Al-Li Alloy Particles in High Pressure Air/N2

Exploring the Combustion Mechanism of Single Micron-Sized Aluminum Particles with a Numerical Model

Synthesis of LiNiO2 cathode materials with homogeneous Al doping at the atomic level

Enhancement effect of Li addition on nitriding reaction and combustion of Al-Li alloy in N 2

Combustion synthesis of fine aluminum nitride powders under micropositive N 2 pressure with water additive

Combustion synthesis of NiAl2O4 spinel powder

Facile Autocombustion Synthesis of La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF) Perovskite Via a Modified Complexing Sol–gel Process with NH4NO3 As Combustion Aid

Combustion Synthesis and Electrochemical Performance of Li [li0.2mn0.54ni0.13co0.13]o2 with Improved Rate Capability

Combustion Synthesis of β-Si<sub>3</sub>N<sub>4</sub> and β-SiAlON with Elongated Prismatic Micro-Crystals by Adding SrCO<sub>3</sub> and NH<sub>4</sub>F

Enhancing the combustion of nAl with AlF 3 coating: gas–solid reaction mechanism for reducing combustion agglomeration of Al powder

Combustion Synthesis Of Beta-Si3n4 And Beta-Sialon With Elongated Prismatic Micro-Crystals By Adding Srco3 And Nh4f

Sodium Fluoroaluminate Promoting the Combustion of Micron-Sized Aluminum Powder with Different Particle Sizes in Carbon Dioxide

Effect of HNO3 treatment on the La0.6Sr0.4Co0.2 Fe0.8O3-δ obtained via combined EDTA-citrate complexing process

Improved ignition and combustion performances of aluminum nanoparticles by in-situ partial conversion of native alumina to surface Al-MOF shell

Effect of HNO3 treatment on the La0.6Sr0.4Co0.2Fe0.8O3-delta obtained via combined EDTA-citrate complexing process

Combustion of aluminum particles in a high-temperature furnace under various O2/CO2/H2O atmospheres

Solution Combustion Synthesis of LiMn2O4 with Different Starting Reactant Compositions