Abstract:Aluminum particles have the problems of difficult ignition, easy agglomeration, incomplete combustion, etc. Therefore, it is of great scientific significance and engineering value to find ways to improve the ignition and combustion performance of aluminum particles in order to promote the full release of energy of aluminum particles. In this paper, spherical nano-sized ferric oxide (nFe 2 O 3 ) and ammonium perchlorate (AP), a commonly used oxidizer in propellants, were used to synergistically improve the ignition and combustion performance of aluminum particles. AP modified the aluminum particles by both mixing and coating methods, respectively. On the basis of coating AP, nFe 2 O 3 was added in order to further enhance the ignition and combustion performance of the aluminum particles. Scanning electron microscope, laser particle size analyzer, thermal analysis system and laser ignition experiment system were used to test the physicochemical properties and ignition combustion performance of different samples. The results showed that AP and nFe 2 O 3 could be coated relatively uniformly on the surface of aluminum particles using the recrystallization method. The thermal reaction behavior of the samples showed that coating was beneficial to the decomposition of AP compared with mixing, and the addition of nFe 2 O 3 could further improve the decomposition efficiency of AP. Ignition and combustion experiments showed that coating AP was more conducive to improving the ignition and combustion performance of aluminum particles than mixing AP, and the addition of nFe 2 O 3 could further significantly enhance the combustion intensity and flame propagation speed of the sample. However, the addition of nFe 2 O 3 increased the ignition delay time of the sample, which may be related to the cold agglomeration phenomenon caused by the nanoparticles. The microscopic combustion flame morphology of different samples showed that coating AP and the introduction of nFe 2 O 3 could significantly reduce the agglomeration phenomenon of aluminum particles. Overall, coating AP reduces the distance between the aluminum particles and the oxidizer, thus significantly improving the ignition and combustion performance of the aluminum particles. The addition of nFe 2 O 3 can further improve the combustion performance of aluminum particles, but at the same time, it also increases the ignition delay time. Hence, the cold agglomeration problem caused by nanoparticles should be fully considered when nFe 2 O 3 is used to improve the ignition and combustion performance of aluminum particles.

Improvement of ignition and combustion performance of micro-aluminum particles by double-shell nickel-phosphorus alloy coating

Improved ignition and combustion performances of aluminum nanoparticles by in-situ partial conversion of native alumina to surface Al-MOF shell

Core-shell particle of aluminum-copper perfluorooctanoate configurations and its ignition and combustion properties

A Promising Strategy to Obtain High Energy Output and Combustion Properties by Self-Activation of Nano-Al

Micro-aluminum powder with bi- or tri-component alloy coating as a promising catalyst: Boosting pyrolysis and combustion of ammonium perchlorate

Enhancing the combustion of nAl with AlF 3 coating: gas–solid reaction mechanism for reducing combustion agglomeration of Al powder

Characteristics of Gasless Combustion of Core-Shell Al@NiO Microparticles with Boosted Exothermic Performance

Laser-Induced Ignition and Combustion of Single Micron-Sized Al-Li Alloy Particles in High Pressure Air/N2

Influence of the Hierarchy Structure of Aluminum Particles on Density, Combustion Efficiency, and Ignition Delay

Preparation of high-energy Al-Li alloy powders with enhanced compatibility and combustion performance by dense fluorosilane polymer composite coating

Enhancement effect of Li addition on nitriding reaction and combustion of Al-Li alloy in N 2

AP and nFe2O3 synergistically improve the ignition and combustion performance of aluminum particles

Preparation of core-shell structured Al-5Li@HTPB powders with improved stability and combustion performance by using perfluoroalkylsilane as a surfactant

AP and Nfe 2 O 3 Synergistically Improve the Ignition and Combustion Performance of Aluminum Particles

Modifying the ignition, combustion and agglomeration characteristics of composite propellants via Al-Mg alloy additives

Preparation and characterization of core-shell Al@PFHP with improving the combustion and ignition properties of aluminum powder

Anti-sintering behavior and combustion process of aluminum nano particles coated with PTFE: A molecular dynamics study

Ignition and combustion of Al and ammonium perchlorate-coated Al particles in a double oxidizing air–H2O–Ar atmosphere

Preparation of an Aluminum Powder Composite with Double-Shell Nanostructure: Enhanced Thermal Conductivity Utilizing a Magnetic Orientation Effect

Design and Controllable Synthesis of Core-Shell Nanostructured Ni-P Particles with an Ionothermal Strategy

An approach to the induced reaction mechanism of the combustion of the nano-Al/PVDF composite particles