Abstract:The non-oxide-reinforced phase AlN-SiC solid solution with high performance was successfully synthesized in the resin-bonded Al-Si-SiC composites under flowing nitrogen at 1300 °C. The AlN-SiC solid solution was synthesized by three paths of liquid-solid, gas-solid and gas-gas reactions through modulation of Al/Si ratio, and controllable microstructure of AlN-SiC solid solution was attained. The phase composition and microstructure of the sintered samples were characterized by XRD and SEM, combined with thermodynamics, the formation mechanism of AlN-SiC solid solution was investigated and the reaction model was established. Al was not detected while Si was detested by XRD. Granular, short columnar and whisker-like AlN-SiC solid solution were generated and their positions varied. As the temperature increases, the partial pressure of oxygen decreases due to the oxidation of Al, Si and SiC on the surface of the sample, inside the sample, the active oxidation takes place, generating Al2O(g), SiO(g) and CO(g). Due to the low oxygen partial pressure, Al is preferentially nitrided to form a thin AlN layer on its surface. The AlN layer is broken as the temperature increases, then liquid Al with carbon from resin begins to flow, leaving the residual shell of AlN in situ. When it flows to the surface of Si, Al-Sialloy is formed locally inside the Si particles under the wetting effect of C, then hexagonal AlN-SiC solid solution is formed inside the Si shell. Part of SiO(g) + CO(g) diffuses into the interior of the AlN residual shell and reacts by aggregation to form a granular AlN-SiC solid solution in the shell wall; others diffuses into the pores of the sample for vapor deposition, and finally forms stacked hexagonal flaky whiskers. The in-situ generated of AlN-SiC solid solution with multiple morphologies in the composite plays a joint toughening effect, which can significantly enhance the comprehensive performance of the composite. In this experiment, the synthesis of AlN-SiC solid solution without sintering aids under normal pressure at a low temperature. It is expected to be applied to the blast furnace and to realize the longevity of blast furnace.

Combustion Synthesis of ZrN and AlN Using Si3N4 and BN As Solid Nitrogen Sources

Structural Formation and Mechanism in Combustion Synthesis of Nitrogen Ceramics (AIN, Si<sub>3</sub>N<sub>4</sub> and AIN-SiC)

In Situ Combustion Synthesis of TiB<sub>2</sub>-AIN Composites

Combustion Synthesis of AlN–SiC Solid Solution Particles

Combustion synthesis of AlN-SIC solid solutions

Combustion synthesis of α-Si3N4 powders using in-situ nano-SiO2 coated Si and Si3N4 reactants

Combustion Synthesis of Rod-Like AlN Nanoparticles

Effect of the Diluent on Combustion Synthesis of Silicon Nitride

Combustion synthesis of fine aluminum nitride powders under micropositive N 2 pressure with water additive

Synthesis of nearly spherical AlN particles by an in-situ nitriding combustion route

Reaction Synthesis of Ceramic Composites Containing In Situ Formed Boron Nitride as Dispersed Phase

Effects of ZrO 2 on the Nitridation Behavior and Mechanical Properties of Reaction-Bonded Si 3 N 4 /H-Bn Composite

Synthesis of a Nitrided Composite Material from Ferroalumosilicozirconium during Combustion

Reaction synthesis of high performance boron nitride-containing composites (BNCC)

Synthesis of Oxynitride Composites during Combustion of a Ferrosilicon–Natural Mineral–Aluminum Mixture in Nitrogen

Synthesis mechanism of AlN–SiC solid solution reinforced Al2O3 composite by two-step nitriding of Al–Si3N4–Al2O3 compact at 1500 °C

Preheating-assisted Combustion Synthesis of Β-Si3n4 Powders at Low N2 Pressure

Combustion Synthesis Of Beta-Si3n4 And Beta-Sialon With Elongated Prismatic Micro-Crystals By Adding Srco3 And Nh4f

In-Situ Reactive Synthesis of AlN-SiC Composites and Solid Solutions

Combustion Synthesis of β-Si<sub>3</sub>N<sub>4</sub> and β-SiAlON with Elongated Prismatic Micro-Crystals by Adding SrCO<sub>3</sub> and NH<sub>4</sub>F

Formation mechanism of AlN-SiC solid solution with multiple morphologies in Al-Si-SiC composites under flowing nitrogen at 1300 °C