Abstract:In this work, surface analysis technology is employed to investigate the removal mechanism and the selection of abrasive during fused silica chemical mechanical polishing (CMP). Morphology of abrasives is inspected by scanning electron microscope (SEM). The atomic force microscope (AFM) is used to determine the surface roughness (Rq) and undulating (PV) of the polished fused silica surface. The results show that abrasive morphology has a tremendous influence on removal rate (MRR) and PV but has little effect on the Rq. The AFM and infrared spectroscopy (IR) analysis show that a soft layer, called “silica gel membrane (SGM),” existed on the polished surface is the critical reason for the differences of MRR, Rq, and PV during CMP. For three kinds of micro-ceria abrasives, the abrasive with a rougher surface gets more opportunities to contact the surface of fused silica, yielding higher MRR. Regarding different kinds of nano-abrasives, there are more SGM induced by nano-ceria abrasive resulting from higher chemical reaction rate. The element contaminations on the polished fused silica have been assessed using X-ray photoelectron spectroscopy (XPS), and the results suggest that there are depths of 3.6 and 5.4-nm element contaminations on the polished surface of fused silica with nano-ceria and nano-alumina abrasives, respectively. While the surface polished by nano-silica is free of heterogeneous element contaminations. Based on study results, a novel polishing slurry is designed by modifying the chemical composition of nano-silica. Comparing with ceria-based slurry, the silica-based slurry has better removal efficiency, and surface quality in fused silica precision machining. © 2019 John Wiley & Sons, Ltd.

Study on Pitch Performance Deterioration in Chemical Mechanical Polishing of Fused Silica

Elastoplastic contact model of pitch-based rough surface and its polishing characteristics

Characteristics of Slurry Recycling in Chemical Mechanical Polishing (CMP) of Fused Silica (FS)

The Cycle Characteristics of Slurries in Chemical Mechanical Polishing (CMP) of Fused Silica

Application of surface analysis in study on removal mechanism and abrasive selection during fused silica chemical mechanical polishing

The Deterioration Characteristics and Mechanism of Polishing Pads in Chemical Mechanical Polishing of Fused Silica

Achieving Ultralow Surface Roughness and High Material Removal Rate in Fused Silica Via a Novel Acid SiO2 Slurry and Its Chemical-Mechanical Polishing Mechanism

Polishing Properties of Porous Silica Abrasive on Hard Disk Substrate CMP

Non-spherical abrasives with ordered mesoporous structures for chemical mechanical polishing

Preparation of Silane Modified Sio2 Abrasive Particles and Their Chemical Mechanical Polishing (cmp) Performances

Investigation into Chemo-Mechanical Fixed Abrasive Polishing of Fused Silica with the Assistance of Ultrasonic Vibration

Surface Morphology Evolution during Chemical Mechanical Polishing Based on Microscale Material Removal Modeling for Monocrystalline Silicon

Investigation of the Chemical Residuals on the Fused Silica During Chemical Mechanical Polishing

Factors Affecting the Surface Quality in Optics Polishing Process

Research on Surface Topography of Silicon Wafer in Chemical-mechanical Polishing

Study on Chemical Mechanical Polishing Performances of Sapphire Wafer (0001) Using Silica-Based Slurry

XPS, UV–vis Spectroscopy and AFM Studies on Removal Mechanisms of Si-face SiC Wafer Chemical Mechanical Polishing (CMP)

Chemical Mechanical Polishing for Monocrystal SiC Assisted by the Heterogeneous Sono-Fenton Oxidation

Chemical Mechanical Polishing of 4H-SiC Wafer with UV-LED Light

Novel green chemical mechanical polishing of fused silica through designing synergistic CeO 2 /h-BN abrasives with lubricity

Chemical Mechanical Polishing (CMP) of On-Axis Si-face 6H-Sic Wafer for Obtaining Atomically Flat Defect-Free Surface