Abstract:Magnetorheological elastomers (MRE) are intelligent controllable materials used as polishing pads in chemical mechanical polishing (CMP), and the magnetic particles in the MRE polishing pad are used as solid-phase catalysts for heterogeneous Fenton reactions for oxidizing single-crystal SiC surfaces, thereby helping reduce the processing difficulty and obtain high-quality surfaces. The influence of the solid-phase catalyst (Fe3O4 mass fraction, particle size) and polishing solution environment (H2O2 concentration, pH value) on the CMP heterogeneous Fenton reaction polishing single-crystal SiC were investigated. The material removal behavior of the MRE polishing pad was investigated. The results demonstrated that the solid-phase catalyst, Fe3O4, has a better superior effect than the carbonyl iron powder (CIP). The polishing material removal rate (MRR) increased and the surface roughness (Ra) decreased with an increase in the Fe3O4 mass fraction. Superior polishing results were obtained at a particle size of 0.3 μm. The higher the H2O2 concentration in the polishing solution, the greater the MRR, with lower Ra at 10% concentration. The highest MRR and lowest Ra were achieved at pH = 3 in acidic environments. During polishing, the heterogeneous Fenton reaction can significantly enhance the removal ability of polishing materials. The MRR increased by 33.4% with the heterogeneous Fenton reaction compared with those without the heterogeneous Fenton reaction, and the contribution of the heterogeneous Fenton reaction to total material removal was 25.03%. The analysis of the SiC–Abrasive–MRE polishing pad contact state revealed that the heterogeneous Fenton reaction can oxidize the SiC surface and reduce the surface hardness, increasing the indentation depth δwa of the abrasive grain into the SiC surface and exhibiting greater material removal.

Chemical Mechanical Polishing for Monocrystal SiC Assisted by the Heterogeneous Sono-Fenton Oxidation

Oxidation Anisotropy of 4H-Sic Wafers During Chemical-Mechanical Polishing

Improvement in chemical mechanical polishing of 4H-SiC wafer by activating persulfate through the synergistic effect of UV and TiO2

Mechanism of chemical and mechanical mutual promotion in photocatalysis-assisted chemical mechanical polishing for single-crystal SiC

Recent Advances In Silicon Carbide Chemical Mechanical Polishing Technologies

Study on heterogeneous Fenton reaction parameters for polishing single-crystal SiC using magnetorheological elastomers polishing pads

Chemical Mechanical Polishing (CMP) of On-Axis Si-face 6H-Sic Wafer for Obtaining Atomically Flat Defect-Free Surface

Picosecond Laser-Assisted Chemical Mechanical Polishing (CMP): Aiming at the Si-Face of Single-Crystal 6H-Sic Wafer

Improved Chemical Mechanical Polishing Performance in 4H-Sic Substrate by Combining Novel Mixed Abrasive Slurry and Photocatalytic Effect

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

XPS, UV–vis Spectroscopy and AFM Studies on Removal Mechanisms of Si-face SiC Wafer Chemical Mechanical Polishing (CMP)

Development of core–shell SiO 2 @A-TiO 2 abrasives and novel photocatalytic chemical machinal polishing for atomic surface of fused silica

Chemical Mechanical Polishing (CMP) of SiC Wafer Using Photo-Catalyst Incorporated Pad

Chemical Mechanical Planarization (cmp) of On-Axis Si-Face Sic Wafer Using Catalyst Nanoparticles in Slurry

Accelerated C-face polishing of silicon carbide by alkaline polishing slurries with Fe3O4 catalysts

Development of Core–shell SiO2@A-TiO2 Abrasives and Novel Photocatalytic Chemical Machinal Polishing for Atomic Surface of Fused Silica

Surface modulation to enhance chemical mechanical polishing performance of sliced silicon carbide Si-face

Investigation on Material Removal Mechanisms in Photocatalysis-Assisted Chemical Mechanical Polishing of 4H–SiC Wafers

Atomic Surface of Silicon Wafers Induced by Grafted Silica Nanoparticles and Sodium Carbonate

Investigation On Smoothing Silicon Carbide Wafer With A Combined Method Of Mechanical Lapping And Photocatalysis Assisted Chemical Mechanical Polishing

Chemical Mechanical Polishing of 4H-SiC Wafer with UV-LED Light