Abstract:The surface modification by ultra-fast laser could regulate the mechanical properties of hard and brittle materials. Since silicon carbide (SiC) is too hard to be machined with acceptable removal rate and quality by mechanical abrasives, and femtosecond laser (fs-laser) assisted grinding could be a potential method to improve the machinability of SiC. Under fs-laser modulating, SiC surface could be modified to generate laser-induced periodic surface structures (LIPSS). Understanding the mechanical properties and material removal mechanism of the LIPPS surface is crucial to accomplish a high efficiency and quality machining process. This paper aims to investigate the effects of fs-laser modification on the mechanical properties, removal mechanism, removal efficiency, and microstructure changes of 4H-SiC surface during removal, together with those of the original 4H-SiC surface for comparison. The hardness and elastic recovery ability of the modified layer are determined by nanoindentation test, and the nano-scratch test is adopted to study the materials removal behavior. The removal efficiency and the quality of the modified surface is significantly improved. Phase transformation is observed in the scratching area, which reveals the existence of ductile mode removal. Moreover, the stress distribution and the change of scratching force on the surface of SiC before and after modification are studied by finite element method (FEM). The results show that the stress distribution and transmission when scratched on the modified surface is lower than that of the original surface, and the scratching force under the same scratch conditions is greatly reduced. With the understanding of materials removal behavior from the whole process of deformation, phase transformation, and separation of LIPPS from substrate, then the fs-laser modification of SiC could be evidenced as an effective method to improve the grinding efficiency and quality in mass production of industry.

Surface modulation to enhance chemical mechanical polishing performance of sliced silicon carbide Si-face

Chemical Mechanical Polishing (CMP) of On-Axis Si-face 6H-Sic Wafer for Obtaining Atomically Flat Defect-Free Surface

Improved Chemical Mechanical Polishing Performance in 4H-Sic Substrate by Combining Novel Mixed Abrasive Slurry and Photocatalytic Effect

Picosecond Laser-Assisted Chemical Mechanical Polishing (CMP): Aiming at the Si-Face of Single-Crystal 6H-Sic Wafer

Oxidation Anisotropy of 4H-Sic Wafers During Chemical-Mechanical Polishing

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

Mechanism of chemical and mechanical mutual promotion in photocatalysis-assisted chemical mechanical polishing for single-crystal SiC

Femtosecond laser modification of silicon carbide substrates and its influence on CMP process

Nanosecond Laser Irradiation Assisted Chemical Mechanical Polishing (CMP) Process for Promoting Material Removal of Single Crystal 4H-Sic

Tribochemical mechanisms of abrasives for SiC and sapphire substrates in nanoscale polishing

XPS, UV–vis Spectroscopy and AFM Studies on Removal Mechanisms of Si-face SiC Wafer Chemical Mechanical Polishing (CMP)

Non-spherical abrasives with ordered mesoporous structures for chemical mechanical polishing

Mechanistic difference between Si-face and C-face polishing of 4H–SiC substrates in aqueous and non-aqueous slurries

Surface Morphology Evolution during Chemical Mechanical Polishing Based on Microscale Material Removal Modeling for Monocrystalline Silicon

Study on material removal mechanism in ultrasonic chemical assisted polishing of silicon carbide

Anisotropy of Chemical Mechanical Polishing in Silicon Carbide Substrates

Recent Advances In Silicon Carbide Chemical Mechanical Polishing Technologies

Investigation on Material Removal Mechanisms in Photocatalysis-Assisted Chemical Mechanical Polishing of 4H–SiC Wafers

Atomic Surface of Silicon Wafers Induced by Grafted Silica Nanoparticles and Sodium Carbonate

Polishing Mechanism of CMP 4H-SiC Crystal Substrate (0001) Si Surface Based on an Alumina (Al2O3) Abrasive

Materials removal mechanism of single crystalline SiC with laser-induced periodic surface structures (LIPSS)