Abstract:Publication date: 15 June 2021 Source: Materials Science Forum Vol. 1034 Author(s): Md Tanwir Alam Porosity is one of the main difficulty to fabricate the superior quality of aluminium matrix composites (AMCs) because it effects the surface finish of the casting, mechanical properties and corrosion resistance. Therefore, porosity must be minimum as possible so that better casting can be produced with optimal properties of the composites. In this study, aluminium matrix nanocomposites (A356/SiC or AMNCs) were fabricated through two-step stir casting via mechanical alloying using ball mill. The matrix alloy (A356) was reinforced with SiC nanoparticles of 40-55 nm avarage particle size (APS). The corrosion was performed by simple immersion corrosion test method for a predefined environment (3.5% NaCl solution) and for the specified duration. The results showed that density and porosity increase with the addition of reinforcement. The corrosion resistance get reduced with the incorporation of SiC due to the increase in porosity and number of nucleation sites. The substantial correlation between the corrosion rate and the amount of SiC are depicted. Moreover, the corrosion rate decreased with the increase in exposure time which is due to the formation of passive layer. The EDS spectrum shows the presence of different constituents in the composites. The formation of the cracks, oxides, pitting corrosion, and localized corrosion are found by the SEM results. Further, SEM of the corroded surface verifies the presence and good distribution of the SiC nanoparticles in the fabricated nanocomposites.

Preparation and Properties of Nano-Sicp/a356 Composites Synthesised with a New Process

Effect of Nano- and Submicron SiC on the α-Al Dendrite Size and Mechanical Strength of SiC/A356 Composites

Physical, Corrosion and Microstructural Analysis of A356/SiC Nanocomposites Fabricated through Stir Casting Process

Preparation and Properties of Nano-sized SiC Particles Reinforced ADC12 Aluminum Matrix Composites

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

Effect of Nano-Sic Content on Mechanical Properties of Sic/2014al Composites Fabricated by Powder Metallurgy Combined with Hot Extrusion

Enhanced Mechanical Behavior and Fabrication of Silicon Carbide Particles Covered by In-Situ Carbon Nanotube Reinforced 6061 Aluminum Matrix Composites

Preparation and properties of nano-sized SiC particles reinforced AZ91D magnesium matrix composites

Effects of nanoparticles on the solution treatment and mechanical properties of nano-SiCp/Al-Cu composites

Mechanical Properties and Microstrutures of Nano-Sized Sic Particles Reinforced Az91d Nanocomposites Fabricated by High Intensity Ultrasonic Assisted Casting

Mechanical and Electrical Properties of Nano Al-Matrix Composites Reinforced with SiC and Prepared by Powder Metallurgy

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Untrasonic-Assisted Fabrication of SiC Nanoparticles Reinforced Aluminum Matrix Composites

Effects of SiC Nanoparticle Content on the Microstructure and Tensile Mechanical Properties of Ultrafine Grained AA6063-SiCnp Nanocomposites Fabricated by Powder Metallurgy

Microstructure and Mechanical Properties of In-Situ Nano Γ-Al2o3p/a356 Aluminum Matrix Composite

Surface Modified Reinforcements on the Structure Properties of A356/SiC Stir Cast Composite

Al-Si/SiC nanoparticles composites synthesized by double stir casting

Microstructure Characteristics of A356 Nanocomposites Manufactured via Ultrasonic Cavitation Processing Under Controlled Solidification Conditions

Development of high-performance aluminium 6061/SiC nanocomposites by ultrasonic aided rheo-squeeze casting method

Nucleation Catalysis in Aluminum Alloy A356 Using Nanoscale Inoculants

Implications of SiC/Al2O3 Reinforced Al-Mg-Zn Alloy Hybrid Nano Composites Using Vacuum Sintering Method