Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Mechanical and Electrical Properties of Nano Al-Matrix Composites Reinforced with SiC and Prepared by Powder Metallurgy

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Investigation of Mechanical and Tribological Properties of Al–7 Wt.% Si alloy Metal Matrix Composites Reinforced with SiC

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

Fabrication of SiC reinforced aluminium metal matrix composites through microwave sintering

Preparation and Properties of Nano-sized SiC Particles Reinforced ADC12 Aluminum Matrix Composites

Microstructure and mechanical properties of SiC-Al2O3 nanocomposite prepared by surface modified SiC nanopowders

Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

Study of Microstructural and Mechanical Properties of Al/SiC/TiO2 Hybrid Nanocomposites Developed by Microwave Sintering

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Role of Different Fractions of Nano-size SiC and Milling Time on the Microstructure and Mechanical Properties of Al–SiC Nanocomposites

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Influence of Nano-Hybrid Reinforcements on the Improvement Strength, Thermal Expansion and Wear Properties of Cu–SiC–Fly Ash Nanocomposites Prepared by Powder Metallurgy

Fabrication of Al/Al2O3/ SiC/graphene hybrid nanocomposites from Al-dross by powder metallurgy: Sinterability, mechanical and electrical properties

Preparation and properties of nano-sized SiC particles reinforced AZ91D magnesium matrix composites

Machinable and mechanical properties of sintered Al 2 O 3 -Ti 3 SiC 2 composites

Sintering temperature-microstructure-property relationships of alumina matrix composites with silicon carbide and silica additives

Microstructure characterization and mechanical properties of in situ synthesized Ti2(Al,Si)C reinforced Al composites

Effect of SiC on Microstructure and Mechanical Properties of Nano-SiC/Mg-8Al-1Sn Composites