Abstract:This study focuses on the effects of hybrid reinforcement consisting of nanosized particles of Palm Sprout Shell Ash (PSSA) and silicon carbide (SiC) on the mechanical and tribological properties of the Al-Cu-Mg alloy. Hybrid reinforced composites with different weight percentages of SiC and PSSA (0:0, 0:4, 1:3, 2:2, and 4:0 wt%) were prepared using the ultrasonic-assisted bottom-poured stir casting technique. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) were used to characterize the hybrid composite made of Al-Cu-Mg alloy. The optical and SEM microstructural analyses demonstrated an even distribution of SiC and PSSA nanosize reinforcements within the matrix. The EDS analysis revealed SiC and PSSA reinforcement particles in the composite. The mechanical properties (tensile, flexural, and impact strength) and wear properties (wear rate and coefficient of friction) of the composites and alloys were evaluated according to the ASTM standards. The hybrid reinforced composites outperformed the base alloy. Among all composites, the 2:2 wt% SIC and PSSA hybrid-reinforced composites exhibited a significant enhancement in both tensile and flexural strength, with a 22.64% and 27.64% increase in strength, respectively. However, the inclusion of these reinforcements led to a reduction in the ductility and impact strength of the Al-Cu-Mg alloy composite. The 0:4 wt% SiC- and PSSA-reinforced composites experienced the largest reductions in ductility and impact strength, with decreases of 47.67% and 4.38%, respectively. For the 2:2 wt% SiC and PSSA composites, these reductions were 23.64% and 3.19%, respectively. The SEM analysis of the fractured surfaces of the composites tested for mechanical properties revealed evidence of both ductile and brittle fracture mechanisms in the tensile, flexural, and impact tests. The wear behaviour of the prepared samples was evaluated, and all composites exhibited superior performance compared with the base alloy, demonstrating adhesive and abrasive wear mechanisms and varying friction coefficients. Among all the composites, the 2:2 wt% SiC- and PSSA-reinforced composites exhibited high wear resistance and a lower coefficient of friction than the other fabricated composites.

Surface Modified Reinforcements on the Structure Properties of A356/SiC Stir Cast Composite

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Microstructural, mechanical and corrosion behaviour of Al–Si alloy reinforced with SiC metal matrix composite

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Enhancing Aluminum-Based Composite Manufacturing: Harnessing Si3N4 Reinforcement via Stir Casting Technique

Physical, Corrosion and Microstructural Analysis of A356/SiC Nanocomposites Fabricated through Stir Casting Process

Compressive Strength, Wear, and Structure Characteristics as a Result of Silicon Carbide Addition on a Copper Base

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Appraisal of tribological properties of A356 with 20% SiC composites under dry sliding condition

Corrigendum: A study on the effects of hybrid (SIC- PSSA) nano sized reinforcement on mechanical and tribological behaviour of Al alloy-based metal matrix composite produced by ultrasonic assisted stir casting (2024 Mater. Res. Express 11 075010)

Mechanical Test on Aluminum Alloy with Maximal Soluble SiC Reinforcement

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Investigating the Effect of Particle Sizes of SiC and Graphite on Strengthening of Aluminium Metal Matrix Composites

FE simulation of uniaxial tensile behavior of SiC reinforced AA5083 alloy

Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass fiber Hybrid Composites

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Enhancement of Wettability of Aluminum Based Silicon Carbide Reinforced Particulate Metal Matrix Composite

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Investigation of Mechanical and Tribological Properties of Al–7 Wt.% Si alloy Metal Matrix Composites Reinforced with SiC

Analysis and Experimental Investigation of A356 Aluminium Alloy Hybrid Composites Reinforced with Gr-FE3O4-B4C Nanoparticles Synthesised by Selective Laser Melting (SLM)