Abstract:The effects of annealing temperature and heating rate on the microstructure, magnetic, and mechanical properties of melt-spun Fe81.7−xSi4B13Cu1.3Nbx (x = 0–4) alloy ribbons have been investigated. With increasing the annealing temperature, a ductile–brittle transition occurs during amorphous structure relaxation, the brittleness becomes severe with more α-Fe precipitation, and the hardness rises continuously. After annealing at respective optimum temperatures under the heating rate of 20 K/min, as the Nb content increases from 0 to 4 at.%, average grain size (Dα-Fe) and volume fraction (Vα-Fe) of the α-Fe in the nanocrystalline alloys decrease gradually from 53.3 nm and 52% to 8.7 nm and 42%, respectively; the strain at fracture (εf) representing ductile level increases from 1.33 to 1.72%; and the coercivity (Hc), saturation magnetic flux densities (Bs), and Vickers hardness (Hv) all decrease gradually. As the heating rate rises from 10 to 400 K/min, the Dα-Fe of the Fe81.7Si4B13Cu1.3 alloy decreases from 45.7 to 28.4 nm without considerable variation of the Vα-Fe; the Hc lowers from 235 to 25 A/m, the εf increases from 1.10 to 1.66%, and the Bs and Hv change slightly. Enriching of Nb weakens the dependence of nanostructure, magnetic softness, and annealing embrittlement on the heating rate. A correlation of εf ∝ Dα-Fen is found for the nanocrystalline alloys, where the n rises from − 1 to − 1/2 with enriching of Nb from 0 to 4 at.%. The mechanisms by which nanostructure affects magnetic and mechanical properties have been discussed.

Microstructural Evolution of Amorphous Si2BC3N Nanopowders Upon Heating at High Temperatures: High Pressures Reverse the Nucleation Order of SiC and BN(C)

Crystallization Behavior of Amorphous Si2bc3n Ceramic Monolith Subjected to High Pressure

Effect of High Pressure on Microstructure of Crystallizing Amorphous Nd9Fe85B6 Alloy

Comparative study on the microstructure evolution and crystallization behavior of precursor-derived and mechanical alloying derived SiBCN

High‐Pressure Synthesis of Amorphous Si3N4 and SiBN‐based Monoliths Without Sintering Additives

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Crystallization and Raman Shift of Array-Orderly Silicon Nanowires after Annealing at High Temperature

Synthesis Mechanism of Amorphous Si2BC3N Powders: Structural Evolution of 2si‐bn‐3c Mixtures During Mechanical Alloying

Characterization of the Interface Region During the Agglomeration of Silicon Nanocrystals in Silicon Dioxide

Direct Synthesis of Sp3‐hybridized BCN Compound by High Pressure and Temperature

Nano-Phase and SiC–Si Spherical Microstructure in SiC/Al-50Si Composites Solidified under High Pressure

Characterization and Microstructural Evolution of Continuous BN Ceramic Fibers Containing Amorphous Silicon Nitride

Phase evolution and oxidation resistance of Si3N4/HfB2/HfB C N1–– ceramic nanocomposites prepared from tailored preceramic polymers

Effect of Annealing Conditions on Microstructural Development and Phase Transformation in Silicon Carbide

Synthesis and Characterization of Superconducting NbC Nanotubes

Density modified structure and mechanical properties of amorphous Si2BC3N by ab‐initio molecular dynamics calculations

Theoretical and experimental study of the mechanism for preparation of SiC nanowires by carbothermal reduction

Microstructure evolution and grain growth mechanisms of h-BN ceramics during hot-pressing

Microstructure and mechanical properties of h-BN–SiC ceramic composites prepared by in situ combustion synthesis

Effects of annealing temperature and heating rate on microstructure, magnetic, and mechanical properties of high-Bs Fe81.7−xSi4B13NbxCu1.3 nanocrystalline alloys

Microstructure evolution and phase transformation of amorphous BCN–SiC composites prepared by two synthetic routes