Abstract:The 3D tri-gate FinFET device architecture is a key transistor scaling to 22nm node and beyond for its excellent short-channel performance[1]. However, compared with planar transistors, it poses greater challenge in the finFET gate etch.[2] As shown in fig.1, the etch needs to stop on top of the fin while etching further down to the STI oxide layer. Therefore, the top of fin needs to endure long time over etch without any structural damage which would adversely affect device performance. What’s more, the gate profile must be vertical and there should not be residual in the corner of gate and fin. It is not an easy task to achieve, at the same time, the three goals of vertical gate profile, no residual in the corner of fin and gate, as well as no structure damage on the top of fin, due to an unavoidable tradeoff. More specifically, vertical gate profile and no residual in the corner of fin demand strong etch function and light polymer, while no structure damage in the top of fin requires weak etch function and heavy polymer, which points to high etch selectivity of silicon to oxide layer. To achieve good etch results, one often falls into this dilemma. As far as we know, few publicly available papers have provided satisfactory solutions to the above- mentioned problem. In this work, we deal with it. The process of gate stack with CD below 30nm is illustrated in fig.2. Then, a HBr/O2 process in transformer coupled plasma is applied to finFET gate etch. As shown in fig.3, gate profile is vertical, fin is well protected and no residual appears in the corner fin. In conclusion, an HBr/O2 plasma etch process of finFET gate with CD below 30nm is investigated.Through appropriate tradeoff , an etch result of vertical gate profile, no residual in the sidewall and corner of fin, no structure damage on the top of fin is achieved.

Ultra-Narrow Si Fins with Low Ler/Lwr for 16/14nm Node Fabricated by 1d Hard Mask Wet Trimming

A strategy to fabricate nanostructures with sub-nanometer line edge roughness

(Digital Presentation) Uniformity and Profile Improvement of Fin Etching Process at Wafer Extreme Edge for Finfet Mass Production

Optimization of Wet strip after Metal Hard Mask All-in-One Etch for metal void reduction and yield improvement

Finfet Gate Etch Towards 16nm Node CMOS Technology

5 NM FIN SAQP PROCESS DEVELOPMENT AND KEY PROCESS CHALLENGE DISCUSSION

Effects of Ultra-Thin Si-fin Body Widths Upon SOI PMOS FinFETs

Analysis of Linewidth Uniformity and Line Edge/Width Roughness in a 5 Nm Logic SAQP Process

Si Interlayers Trimming Strategy in Gate-All-Around Device Architecture for Si and SiGe Dual-Channel CMOS Integration

Strategy for line width roughness (LWR) reduction in carbon mandrel patterning

A Capped Trimming Hard-Mask Patterning Technique For Integration Of Nano-Devices And Conventional Integrated Circuits

Novel 14-nm Scallop-Shaped FinFETs (S-FinFETs) on Bulk-Si Substrate

Investigation of Fabricated CMOS FishboneFETs and TreeFETs with Strained SiGe Nano-fins on Bulk-Si Substrate

Fabricating 3D Si nanostructure via a novel Ga+ implantation enabled maskless dry etching process

Fabrication of Nanopore and Nanopore Arrays in Si Substrate by Wet Etching Method at Wafer Scale

Effects of Fin Shape on Sub-10 Nm FinFETs

Wafer level microarcing model in 90nm chemical-vapor deposition low-k via etch on 300mm silicon-on-insulator substrate

Langmuir−Blodgett Monolayer Masked Chemical Etching: an Approach to Broadband Antireflective Surfaces

Wafer-Scale Fabrication of V-Shaped Silicon Nano-Slit Arrays

Scalable Submicron Channel Fabrication by Suspended Nanofiber Lithography for Short‐Channel Field‐Effect Transistors

An experimental investigation of silicon wafer thinning by sequentially using constant-pressure diamond grinding and fixed-abrasive chemical mechanical polishing