Abstract:The etch profile control for the amorphous carbon layer (ACL) is an important step in the 3D NAND fabrication process. Because ACL is the mask material for defining the pattern of the high-aspect-ratio-contact (HARC) dielectric ONON layer etch process, precise control of its etch profile is necessary. Specifically, an ideal ACL mask profile should be free of symptoms such as hole circularity distortion, profile twisting, bowing, and undercutting. In order to achieve this desired etch performance, knowledge of various etch contributing factors must be systematically derived and applied, including etch surface chemistry, high-aspect-ratio (HAR) etchant transport, ion flux and ion energy angle distribution function (EADF) control, etc. In this work, we investigate the ACL etch fundamental characteristics through combined 2D chamber-scale plasma simulations with the hybrid plasma-equipment model (HPEM) and 3D etch profile simulations with the Monte-Carlo Feature Profile Model (MCFPM) for an inductively-coupled-plasma (ICP) reactor with RF bias at the substrate. In particular, we focus on the profile trends under different reactant fluxes and energies. Our findings indicate that maintaining a neutral-starved (ion-rich) etch regime is essential for mitigating both the channel hole etch circularity distortion and the slit etch profile twisting. To achieve this desired etch regime, the HAR ion, and neutral transport must controlled by the RF bias power and frequency, substrate temperature, etc. Furthermore, especially in this neutral-limited etch regime which is necessary for distortion and twisting mitigation, the control of the consequent aspect-ratio dependent etching (ARDE), as well as maintaining the critical dimension (CD) and reducing bowing and undercutting are also necessary. For this purpose, atomistic density functional theory (DFT) calculations have been applied to compare the reaction energetics for various ALD-like sidewall passivation chemistries. Specifically, we propose a new process based on its favorable reaction energetics. Experimental cross-section images have matched simulation results. In conclusion, our insights have provided guidance for process optimization and tool design to meet industrial demands.

Strategy for line width roughness (LWR) reduction in carbon mandrel patterning

Polymer Pen Chemical Lift-Off Lithography

Investigation of Amorphous Silicon As Dry Etch Hard Mask in BEOL Low-k Dielectric Patterning

Laser Direct Writing System and Its Lithography Properties

Immersion Barc for Hyper Na Applications Ii

Analysis of Linewidth Uniformity and Line Edge/Width Roughness in a 5 Nm Logic SAQP Process

Optimization of Wet strip after Metal Hard Mask All-in-One Etch for metal void reduction and yield improvement

Combining Double Patterning with Self-Assembled Block Copolymer Lamellae to Fabricate 10.5 Nm Full-Pitch Line/space Patterns

Step Coverage and Dry Etching Process Improvement of Amorphous Carbon Hard Mask

Development of 90 NM & 5 NM High Resolution Advanced Lithographic Patterning Materials

Enabling faster VSB writing of 193i curvilinear ILT masks that improve wafer process windows for advanced memory applications

14Nm Fin Sadp Patterning Processes and Integration

Effective Optimization Strategy for Electron Beam Lithography of Molecular Glass Negative Photoresist

Wafer level microarcing model in 90nm chemical-vapor deposition low-k via etch on 300mm silicon-on-insulator substrate

High Aspect Ratio Carbon Hard Mask Etch Process for Profile and LCDU Control

A strategy to fabricate nanostructures with sub-nanometer line edge roughness

Ultra-Narrow Si Fins with Low Ler/Lwr for 16/14nm Node Fabricated by 1d Hard Mask Wet Trimming

High-aspect-ratio amorphous carbon mask etch profile control through plasma and surface chemistry optimization

Total Solutions for 40nm Metal Hard-Mask All-In-One Etch Process

Rapid prototyping of etch test structures for hard mask development using electron beam lithography

Measurement and Calculation Method for Sub-20 Nm Line and DSA Patterns