Abstract:This paper presents a novel composite sensor that is monolithically integrated with an accelerometer, a pressure sensor, and a thermometer by using a single-side-processed micromachining technique. Such composite sensors are highly demanded in tire pressure monitoring system (TPMS) applications. Based on heat convection, the accelerometer consists of a microheater and a pair of detector to measure the acceleration-induced temperature distribution change. Thermopile-and thermistor-based detectors both have been used to measure the temperature distribution change. Under a heating power of 10.9, 19.4, and 30.3 mW, the sensitivity of the thermopile-based accelerometer is measured as 37.92, 85.04, and 134.08 mu V/g, respectively (while the thermistor-based accelerometer shows a sensitivity of 25.96, 55.79, and 86.67 mu V/g). The two detecting methods both feature enough frequency range that is higher than 100 Hz. In the pressure sensor, the low-stress silicon nitride diaphragm is designed into a narrow rectangular shape, on which four polysilicon piezoresistors are configured into a Wheatstone bridge. The sensitivity of the 450-KPa-ranged pressure sensor is measured as 45.9 mV/3 V FS, the nonlinearity is +/- 0.84% FS, and the over-range capability is ten times the measured range. The tire temperature monitoring thermometer is also made up of polysilicon and is measured with a linear resistance change versus temperature over the range of -40 degrees C-+ 100 degrees C. In the on-chip integrated sensors, a low-stress silicon nitride thin film is used as the electric isolation layer, the pressure diaphragm, and the heating-insulating freestanding beams. The boron-doped polysilicon film is used as the piezoresistors, the heater, the thermopile, and the thermometer. After wafer-level packaging with an aligned adhesive bonding technique, the 2.5 x 2.5 x 0.84 mm(3) microsensor chips are promising for TPMS low-cost fabrication and volume applications.

Monolithic Integration of Multiple Sensors on a Single Silicon Chip

Crosstalk-free Hybrid Integrated Multimodal Sensor for Human Temperature, Humidity, and Pressure Monitoring

Recent Advances in Monolithic Integration of Diverse Technologies with Si CMOS

Heterogeneous Integration of MEMS Sensor Array and CMOS Readout IC with Through Silicon Via Interconnects

Monolithic integration of micromachined sensors and CMOS circuits based on SOI technologies

A Multimodal Sensing CMOS Imager Based on Dual‐Focus Imaging(Adv. Sci. 14/2023)

3-D Integration and Through-Silicon Vias in MEMS and Microsensors

Design And Realize Of 3d Integration Of A Pressure Sensor System With Through Silicon Via (Tsv) Approach

Fabrication of Monolithic Silicon Multi-Sensor on SOI Wafer

A Design of a Multi-Sensor Platform by System-Level Integration in the Package

On-Chip Integration of Acceleration, Pressure, and Temperature Composite Sensor with A Single-Sided Micromachining Technique

Monolithic Integration of Micro-Cantilever and Readout Circuits

Monolithic Integration of Pressure/Humidity/Temperature Sensors for CMOS-Mems Environmental Sensing Hub with Structure Designs for Performances Enhancement

Implementation of a monolithic soc environmental sensing hub using cmos-mems technique

Integration of infrared sensor and pressure/humidity/temperature cmos-mems environmental sensing hub by local vacuum packaging

Monolithic Integration of Capacitive Sensors Using A Double-Side Cmos Mems Post Process

TSV Integrated and Pattern Recognition Based Multimode Degenerated Low-Power 3-Dimensional Smart Sensing Chips

A Novel Monolithically Integrated Pressure, Accelerometer and Temperature Composite Sensor

A fully-differential, multiplex-sensing interface circuit monolithically integrated with tri-axis pure oxide capacitive CMOS-MEMS accelerometers

Monolithically and Vertically Integrated Environmental Sensing Hub with Novel Air-Based Humidity Sensor Design

ENVIRONMENTAL SENSING HUB ON SINGLE CHIP USING DOUBLE-SIDE POST-CMOS PROCESSES