Abstract:This paper presents a novel composite sensor that is monolithically integrated with an accelerometer, a pressure sensor, and a thermometer by using a single-side-processed micromachining technique. Such composite sensors are highly demanded in tire pressure monitoring system (TPMS) applications. Based on heat convection, the accelerometer consists of a microheater and a pair of detector to measure the acceleration-induced temperature distribution change. Thermopile-and thermistor-based detectors both have been used to measure the temperature distribution change. Under a heating power of 10.9, 19.4, and 30.3 mW, the sensitivity of the thermopile-based accelerometer is measured as 37.92, 85.04, and 134.08 mu V/g, respectively (while the thermistor-based accelerometer shows a sensitivity of 25.96, 55.79, and 86.67 mu V/g). The two detecting methods both feature enough frequency range that is higher than 100 Hz. In the pressure sensor, the low-stress silicon nitride diaphragm is designed into a narrow rectangular shape, on which four polysilicon piezoresistors are configured into a Wheatstone bridge. The sensitivity of the 450-KPa-ranged pressure sensor is measured as 45.9 mV/3 V FS, the nonlinearity is +/- 0.84% FS, and the over-range capability is ten times the measured range. The tire temperature monitoring thermometer is also made up of polysilicon and is measured with a linear resistance change versus temperature over the range of -40 degrees C-+ 100 degrees C. In the on-chip integrated sensors, a low-stress silicon nitride thin film is used as the electric isolation layer, the pressure diaphragm, and the heating-insulating freestanding beams. The boron-doped polysilicon film is used as the piezoresistors, the heater, the thermopile, and the thermometer. After wafer-level packaging with an aligned adhesive bonding technique, the 2.5 x 2.5 x 0.84 mm(3) microsensor chips are promising for TPMS low-cost fabrication and volume applications.

Fabrication of Monolithic Silicon Multi-Sensor on SOI Wafer

Thin Layer Soi-Fets Used for Stress-Sensing and Its Application in Accelerometers

Single Chip-Based Nano-Optomechanical Accelerometer Based on Subwavelength Grating Pair and Rotated Serpentine Springs

Monolithic Integrated Micro-Opto-Electromechanical Accelerometer Based on Michelson Interferometer Structure

Bonding of Aluminum Coated Silicon Wafers Based on Polypropylene Carbonate and As a Multi-Functional Sensor

Monolithic integration of micromachined sensors and CMOS circuits based on SOI technologies

Monolithic Integration of Multiple Sensors on a Single Silicon Chip

Design, Fabrication, and Calibration of a Piezoresistive Stress Sensor on SOI Wafers for Electronic Packaging Applications

Fabrication and Characterization of Monolithic Integrated Three-Axis Acceleration/Pressure/Magnetic Field Sensors

A Novel Monolithically Integrated Pressure, Accelerometer and Temperature Composite Sensor

On-Chip Integration of Acceleration, Pressure, and Temperature Composite Sensor with A Single-Sided Micromachining Technique

A Front-Side Released Single Crystalline Silicon Piezoresistive Microcantilever Sensor

Design, fabrication and testing of a SOI accelerometer

Fabrication and Characterization of a MEMS Thermal Convective Accelerometer on Silicon-in-Glass Substrate

Fabrication of SOI MEMS Inertial Sensors with Dry Releasing Process

A Single-Side Micromachined MPa-Scale High-Temperature Pressure Sensor

High Temperature Pressure Sensor Fabricated with Smart Cut SOI Materials

Fabrication of SiC MEMS Pressure Sensor by Anodic Bonding

Fabrication of 4H-SiC piezoresistive pressure sensor for high temperature using an integrated femtosecond laser-assisted plasma etching method

SOI Micro-Accelerometer Fabricated with Anti-Footing Technique

Fabrication of monolithic integrated bimaterial resonant uncooled IR sensor