Design and Application of Ash Cooler Can Sort of Fine Ash

施正伦,王勤辉,程乐鸣,方梦祥,高翔,施正展,骆仲泱,岑可法

DOI: https://doi.org/10.3969/j.issn.1005-006X.2000.06.002

2000-01-01

Abstract:This paper presents the design of an ash cooler, which functions as a sorter of fine ash as well. The engineering application of this cooler with the corresponding CFB MSW incinerator is also introduced.

What problem does this paper attempt to address?

Operation Issue and Improved Design for Air-water Cooling Ash Cooler

ZHANG Man,BIE Ru-shan

2006-01-01

Abstract:Some issues are appeared in the operation of the circulating fluidized bed(CFB)boiler,especially for ash cooler.The trouble of the ash cooler is analyzed and the improved design is provided.It can be considered in design,commissioning and operating of circulating fluidized bed boilers.
Investigation On The Ash Deposition Of A Radiant Syngas Cooler Using Critical Velocity Model

Pengfei Zhang,Chengzhang Xu,Jianping Kuang,Shuigang Liu,Zhiwen Xia,Ke Wu,Yuqi Huang

DOI: https://doi.org/10.1016/j.egyr.2020.04.015

IF: 5.2

2020-01-01

Energy Reports

Abstract:Coal gasification technology is a very important industrial technology, in which the Radiant Syngas Cooler (RSC) plays a pivotal role in the heat storage and heat recovering process. Ash deposit in RSC is a critical factor which may seriously affect the performance of RSC or even result in a shutdown. Therefore, conducting research on the deposit process of RSC is extremely worthwhile. In this study, we create an RSC model with the application of an optimized Critical Velocity Model (CVM) and perform simulations using the CFD method. With the simulating method, we conduct a series of analysis to obtain a more detailed description of the ash distribution and heat transfer in the RSC. Research shows that the CVM proposed in this paper can be precisely applied to the heat transfer process in a RSC, and not only can this method obtain the distribution of ash deposit similar to other methods but also determine the conversion of the ash deposit thickness to heat resistance, which makes the forecast of the overall heat exchange more accurate. According to the study, the ash thickness changes with the vertical height of RSC. For the division wall and panels, the ash thickness increased from the bottom, and then reached a maximum value at about 2/3 of total height. Under the influence of ash deposition, the total heat transfer rate of RSC decreased by 10.4%, and the outlet temperature of syngas increased by 5.7%. This result can provide a reference for the predictive analysis of RSC. (C) 2020 The Authors. Published by Elsevier Ltd.
Ash Cooler of CFB Boiler and Heat Recover of Slag

姜孝国,张缦,杜守国

DOI: https://doi.org/10.3969/j.issn.1674-1005.2002.04.006

2002-01-01

Abstract:This article introduced some typical ash coolers and their performances. The fluidized bed type ash cooler are introduced emphasisly. Some questions about the heat recover of slag are discussed.
Development of new ash cooling method for atmospheric fluidized beds

Xuantian Li,Zhongyang Luo,Mingjiang Ni,Leming Cheng,Xiangyu Gao,Mengxiang Fang,Kefa Cen

1995-01-01

Abstract:The pollution caused by hot ash drained from the bed is another challenge to atmospheric fluidized bed combustion technology when low-rank, high ash fuels are used. A new technique is developed for ash cooling and utilization of the waste heat of ash. Results from the demonstration of an 1.5 T/H patented device have shown the potential to use this type of ash cooler for drying and secondary air preheating. Bottom ash sized in the range 0-13 mm can be cooled from 1650��F (900��C) to tolerable temperatures for conveying machinery, and the cooled ash can be re-utilized for cement production.
Design and Operation of the Double-Cylinder Rotary Ash Cooler for Large CFB Boilers

Huiren Xiao,Man Zhang,Yang Zhang,Yuge Yao,Qing Liu,Hairui Yang,Junfu Lyu

DOI: https://doi.org/10.1016/j.applthermaleng.2020.115056

IF: 6.4

2020-01-01

Applied Thermal Engineering

Abstract:The bottom ash cooler is an important auxiliary equipment of a circulating fluidized bed (CFB) boiler. As the CFB boiler technology develops, the rotary ash coolers have partially substituted the fluidized bed bottom ash coolers in the industrial practice due to its excellent reliability. To meet the increased output requirement, a double-cylinder rotary ash cooler, rather than the conventional single-cylinder one, was proposed in the present study. This paper provided the design of the double-cylinder rotary ash cooler and presented its application in a 300 MWe CFB boiler. The design parameters, structural features, heat transfer performance, as well as the field trial results were discussed in the present study. In addition, a semi-empirical model was proposed to provide theoretical support for the design principle of the double-cylinder rotary ash cooler. The field trial results showed that the actual output of the installed double-cylinder rotary ash cooler was up to 32 t/h with the ash temperature at the outlet being the designed value, much greater than the value (similar to 23 t/h) of the single-cylinder one at approximately the same size. Particularly, this novel bottom ash cooler had run continuously for more than three years without any maintenances due to its reasonable design.
Experimental Research on a New Cooling Method of CFB Ash

王观华,施正伦,骆仲泱,岑可法,王文龙

DOI: https://doi.org/10.3969/j.issn.1005-006x.2003.01.011

2003-01-01

Abstract:A new cooling method of CFB ash, cooling directly by water, is put forward. Through the study of activation mechanism of CFB ash, the influence of ash activity activated by this method is analyzed. The results indicate that better activity will be obtained by this method with controlled cooled water.
Fluidized Bed Ash Cooler Used in A Circulating Fluidized Bed Boiler: an Experimental Study and Application

Zhang Man,Bie Rushan,Xue Qinggui

DOI: https://doi.org/10.1016/j.powtec.2010.03.004

IF: 5.64

2010-01-01

Powder Technology

Abstract:The performance of a fluidized bed ash cooler was studied using a cold experiment bench. The air flow rate, particle size of the solids and air distributor type are considered to be the key parameters of the operation of a fluidized bed ash cooler (FBAC). It was found that the amount of fluidizing air directly affects the conveying of ash and that they have a quadratic relationship. An acceptable particle size distribution for the solids is d50<450μm. Furthermore, the experiment reveals that the height of the weir in the FBAC does not affect the conveying of the ash flow. The influence of injected air on the transportation of ash is not significant. Optimal air nozzle dimensions are presented.
Effect of Rapid Water-Cooling Process on Desulfurization Performance of CFB Bottom Ash

LI Hao,CHEN Wufeng,WANG Chang’an,CHE Defu

DOI: https://doi.org/10.11949/j.issn.0438-1157.20160227

2016-01-01

Abstract:A rapid water-cooling process to desulfurize high temperature CFB bottom ash was designed for the improvement of poor ash utilization. Apparatus and methods for bench-scale rapid water-cooling and desulfurizing study were established and CFB ashes with and without treatment were characterized for f-CaO content, microscopic structure, and desulfurization efficiency. Through theoretical analysis, a hypothesis, that rapid water-cooling could facilitate destroying shell of CaSO4 particles, was proposed and validated experimentally. Results of SEM/EDX and TGA analyses on treated and non-treated ashes showed that calcium on particle surface increased evidently and the calcium recycling rate could increase about 30% post water-cooling treatment. The desulfurization efficiency enhanced continuously with increasing temperature of CFB bottom ash before rapid water-cooling. When hot CFB ash entered into water, ash particles could burst and destroy CaSO4 shell due to strong thermal stress across particle surface. Since higher temperature of CFB ash prior to water-cooling would result in stronger thermal stress, CaSO4 shell were destroyed more easily and desulfurization efficiency became higher. Thus, the rapid water-cooling process would be a new method for regeneration and reuse of CFB ash by improving desulfurization efficiency, which certainly provided practical guidance for engineering applications.
Comprehensive Utilization of CFB Ashes After Desulfurization

王文龙,施正伦,骆仲泱,岑可法

DOI: https://doi.org/10.3969/j.issn.1005-006X.2002.05.008

2002-01-01

Abstract:The characteristics of CFB ashes are thoroughly studied, and their advantages and disadvantages for comprehensive utilization are analyzed. The way to utilize ashes after pre-hydration disposal is put forward.
C214 DEVELOPMENT OF UTILIZATION OF CFB BOILER ASH

Dengxin Li,Meng Xu,Junfu Lu,Qing Liu,Jiangsheng Zhang,Guangxi Yue,Jiexi Li

DOI: https://doi.org/10.1299/jsmeicope.2003.2._2-247_

2003-01-01

The Proceedings of the International Conference on Power Engineering (ICOPE)

Abstract:The paper first introduces the properties of circulating fluidized bed (CFB) ashes (fly ash and bed ash). Then it describes the new investigations about utilization progress of them. The properties of fly ash and bed ash are not identical, so the progresses of utilization are different, too. Usually, the low carbon and high CaO bed ash can be directly used as material for construction. But the high carbon fly ash must be treated with some process before being utilized, such as hydration for cement, pelletizing for re-burning.
Process design and thermal-calculation of a novel entrained-flow gasifier using fine ash as feedstock

Yue Lu,Zhengqi Li,Yufei Wang,Guangfei Jiang,Fang Neng,Chunchao Huang,Zhichao Chen

DOI: https://doi.org/10.1016/j.apenergy.2023.121395

IF: 11.2

2023-06-26

Applied Energy

Abstract:Fine ash from gasification is produced in huge quantities, and has the carbon content of around 20–––40%. The treatment of fine ash is urgently needed to be resolved. However, large-scale industrial utilization of fine ash has not yet been realized. The ash content of fine ash is 60––70%. The calorific value of fine ash is usually lower than that of coal. The adiabatic combustion temperature of fine ash gasifier is lower than that of pulverized coal gasifier, and the outlet temperature is also lower. This paper pointed out the reason why the outlet temperature of the entrained-flow gasifier was low when fine ash produced by Ende gasifier was used as the gasification feedstock. A novel process of using the entrained-flow gasifier to utilize the carbon in fine ash was proposed. Fine ash in raw syngas was captured by a bag dust collector, mixed with pulverized coal, and transported to the entrained-flow gasifier. The gasification parameters of the process were obtained. When fine ash was used alone as feedstock, it was difficult to reach the required temperature for the discharge of liquid slag. When fine ash and coal were co-gasified, the outlet temperatures were 1461 and 1529 °C, which could meet the gasifier's safe operational requirements for smooth discharge of liquid slag. The syngas concentrations were greatly affected by the carbon content of fine ash. The results of the current work provide a useful reference for industrial design and application of fine ash in atmospheric entrained-flow gasifier.

energy & fuels,engineering, chemical
Experimental Study on Heat Transfer in Rolling Ash Cooler

W. Wang,J. J. Li,S. Yang,X. D. Si,H. R. Yang,J. F. Lu,G. X. Yue

DOI: https://doi.org/10.1007/978-3-642-02682-9_179

2009-01-01

Abstract:From the view of the reliability and the techno-economy, the rolling ash cooler is feasible for the large-scale CFB boilers. However, existing studies on heat transfer in rolling ash cooler mainly focused on heat balance calculation and cold, hot test on the ash cooler outputs. In the heat balance calculation, the value of the overall heat transfer coefficient (a) is usually estimated by the experience, lacking of the support of experimental data.
Application of Ash Agglomeration in Garbage Firing Internally Circulating Fluidized Beds

WANG Bin,TIAN Feng-guo,ZHANG Ming-chuan,FAN Hao-jie

DOI: https://doi.org/10.3969/j.issn.1674-7607.2006.03.012

2006-01-01

Abstract:A proposal is being presented for the application of the ash agglomeration technique for garbage disposal by incineration in internally fluidized beds.Its necessity and feasibility is being analyzed from the chemical composition's point of view of the incineration residues.Modelized hot state agglomeration experiments in a nonuniformly air blasted circulating fluidized bed were conducted by using resin pallets for the bed stuff and microcrystallized wax granules for the material of low melting point.These hot state experiments indicate that partitioned temperature distribution and regionalized coalescence are important factors for warranting the successful application of the ash agglomeration technique;the internal particle flow favors the slag-off process and reduces the lingering time of the sticky mass.Figs 4,table 1 and refs 15.
Energy and Efficiency Analysis of Ash Cooling Equipment of 300 MW Circulating Fluidized Bed Unit

LI Jian-feng,L(U) Jun-fu,LI Bin

2011-01-01

Abstract:In order to improve the heat energy efficiency of hot slag,the thermal-efficiency and exergy-efficiency calculation models of two types of ash cooling equipment of a 300 MW circulating fluidized bed boiler were estab-lished and their performance was calculated. The results show that the two types of cooling equipment differ great in thermal-efficiency and exergy-efficiency,and that their thermal-efficiency is obviously higher than their exergy-efficiency. So to develop ash cooling equipment with a large scale and a high efficiency is essential for energy-saving of a large-scale CFB boiler.
Research of Heat Transfer Model in Rotary Ash Coolers

SI Xiao-dong,WANG Wei,LI Jin-jing

2011-01-01

Abstract:By analyzing the flow and heat transfer process of ash particles in a rotary ash cooler with fins,a one-dimensional heat transfer model was proposed,in which the reburning of residual carbon in bottom ash was considered while the model parameters determined in accordance with relevant reference materials and experimental results.Using the model,temperatures of rotary ash cooler for a 300 MW circulating fluidized bed boiler were predicted,which were then compared with actual operation parameters.Comparison results prove the model to be accurate in predicting ash discharge and cooling water temperatures of rotary ash coolers.
CFD Modeling of Ash Deposition Distribution in an Industrial Radiant Syngas Cooler to Enhance the Operation Performance

Bo Wang,Qinghua Guo,Yan Gong,Jianliang Xu,Guangsuo Yu

DOI: https://doi.org/10.1016/j.cep.2022.109083

IF: 4.264

2022-01-01

Chemical Engineering and Processing - Process Intensification

Abstract:Radiant syngas cooler (RSC) is a crucial heat recovery equipment for entrained-flow coal gasification. Ash depositions in the industrial RSC endanger its operation efficiency and operation safety. In this work, the critical viscosity model and the ash shedding model are coupled to explore the ash deposition behavior in the industrial RSC for a 2000 t/d entrained-flow coal gasifier. Simulation results are in good agreement with the industrial conditions. The results show that ash depositions in RSC are mainly distributed in the upper part and the bottom cone, and the maximum ash thickness are 9.67 mm and 36.71 mm respectively. Due to ash depositions, the outlet temperature of RSC increases by 19.76%, the total heat transfer rate decreases by 21.88%, and the steam yield decreases by 22.41%. Employing low-ash coal as gasification raw coal is a good suggestion to enhance the operation performance of the industrial RSC. Moreover, when the industrial RSC is fully loaded, an appropriate increase in syngas mass flow rate can also contribute to a better operation performance.
Development and Application of the Design Principle of Fluidization State Specification in CFB Coal Combustion

Runxia Cai,Hai Zhang,Man Zhang,Hairui Yang,Junfu Lyu,Guangxi Yue

DOI: https://doi.org/10.1016/j.fuproc.2018.02.009

IF: 8.129

2018-01-01

Fuel Processing Technology

Abstract:In this paper, the design principle of Fluidization State Specification (FSS) is reviewed and its applications in CFB boiler are introduced. In the early 2000s, FSS design principle was proposed to determine the fluidization state in the upper furnace as the basis of engineering design. The principle was initially adopted by engineers to select a proper superficial gas velocity to prevent the severe erosion on water walls. It was used in many CFB furnace designs including the world's largest 600 MW supercritical one in China. Later, FSS design principle was extended to reduce the pressure head of the draft fan to save energy consumption. Industrial application showed that by changing the amount of bed inventory, CFB boilers could operate at a re-constructed fast bed state, not only saving -30% power of the draft fans, but also further reducing the erosion on water walls and improving combustion efficiency. Recently, FSS design principle was further improved and applied to achieve ultra-low NOx and SO2 emission. A third coordinate with improved bed quality, i.e., size distribution of bed material was proposed to add on the original two-dimensional fluidization state diagram defined by the superficial gas velocity and the solid circulation rate. Industrial practices showed that under the guideline of the improved FSS design principle, it was possible for CFB boilers to reach over 99% desulfurization efficiency with limestone injected into furnace, and less than 50 mg/Nm(3) (at 6% O-2) NOx emission at the furnace exit. FSS design principle promotes the booming of ultra-low emission CFB boilers in China.
Design and Operation of Hot Air System with Corn Fired CFB

ZHANG Yan-guo,LI Qing-hai,WANG Lian-sheng,WANG Zhao-jun,REN Gang-lian

DOI: https://doi.org/10.3969/j.issn.1002-6339.2005.04.001

2005-01-01

Abstract:This paper presented the structure of circulating fluidized bed boiler and the hot air system.This hot air system consists of circulating fluidized bed hot water boiler,heat exchanger,control device and dust catcher.The key equipment of this system is the circulating fluidized bed hot water boiler which fired corn-cob which come from corn seedproduct process.The practical operation shows that the corn-cob fired circulating fluidized bed is welcome by corn-seed process enterprise.The further improvement of this system is to enhance the ash blow of the boiler.
Numerical Study on Dynamic Ash Deposition and Heat Transfer Characteristics of Radiant Syngas Cooler

Yao Xiong,Yinhe Liu,Yu Guan,Huizhen Liu,Sajie Geng

DOI: https://doi.org/10.1016/j.energy.2022.125252

IF: 9

2022-01-01

Energy

Abstract:Ash deposition greatly influences the performance of Radiant Syngas Cooler (RSC) which plays a pivotal role in the heat recovering process in coal gasification technology. Therefore, a numerical model of ash deposition coupled with heat transfer is established in present study to predict the ash deposition of RSC, and the effects of inlet temperature and division wall structure on deposition characteristics are further discussed. The simulation results indicate that the particle impact mainly occurs in the transition region of the jet flow to plug flow, while the particle deposit mainly occurs in the recirculation region. The deposition of inner wall and division wall shows a malignant growth pattern successively with the width increase of division wall. The division wall of 400 mm width is more conducive to the safe and stable operation of the RSC than those of 250 mm and 650 mm. The deposition becomes heavy with the increase of inlet temperature, and the deposition of division wall belongs to the slow growth, the large-scale detaching and the malignant growth pattern at the inlet temperature of 1573 K, 1673 K and 1773 K, respectively. Present result may provide a reference for the structural design and operational adjustment of RSC.
Ash Melting Technology and Application in MSW Gasification and Melting System

ZHU Wen-li,CHI Yong,XIAO Gang,WANG Fei

DOI: https://doi.org/10.3969/j.issn.1001-7119.2007.02.027

2007-01-01

Abstract:Gasification melting technology for MSW has attracted attention as the most potential substituted technology for MSW incineration,because it has several outstanding advantages,such as strict pollution control,notice volume reduction,and effective resource utilization.The ash melting process is a key process for dioxins zero emission.In this paper,the basic theory of ash melting technology has been illuminated.The processes and developing statuses of different melting furnaces have been summarized.Moreover,the application in MSW gasificationmelting systems has been introduced.

Design and Application of Ash Cooler Can Sort of Fine Ash

Operation Issue and Improved Design for Air-water Cooling Ash Cooler

Investigation On The Ash Deposition Of A Radiant Syngas Cooler Using Critical Velocity Model

Ash Cooler of CFB Boiler and Heat Recover of Slag

Development of new ash cooling method for atmospheric fluidized beds

Design and Operation of the Double-Cylinder Rotary Ash Cooler for Large CFB Boilers

Experimental Research on a New Cooling Method of CFB Ash

Fluidized Bed Ash Cooler Used in A Circulating Fluidized Bed Boiler: an Experimental Study and Application

Effect of Rapid Water-Cooling Process on Desulfurization Performance of CFB Bottom Ash

Comprehensive Utilization of CFB Ashes After Desulfurization

C214 DEVELOPMENT OF UTILIZATION OF CFB BOILER ASH

Process design and thermal-calculation of a novel entrained-flow gasifier using fine ash as feedstock

Experimental Study on Heat Transfer in Rolling Ash Cooler

Application of Ash Agglomeration in Garbage Firing Internally Circulating Fluidized Beds

Energy and Efficiency Analysis of Ash Cooling Equipment of 300 MW Circulating Fluidized Bed Unit

Research of Heat Transfer Model in Rotary Ash Coolers

CFD Modeling of Ash Deposition Distribution in an Industrial Radiant Syngas Cooler to Enhance the Operation Performance

Development and Application of the Design Principle of Fluidization State Specification in CFB Coal Combustion

Design and Operation of Hot Air System with Corn Fired CFB

Numerical Study on Dynamic Ash Deposition and Heat Transfer Characteristics of Radiant Syngas Cooler

Ash Melting Technology and Application in MSW Gasification and Melting System