Abstract:In this study, an online digital image technique was used to investigate the process of spontaneous shedding of ash deposits when burning Da Tong (DA) coal mixed with 20 wt % rice hull in a pilot-scale furnace. The morphology of shedding deposit, the variation in deposit thickness, and the heat flux during the spontaneous deposit shedding process were all obtained by combining the digital image technique with an oil-cooled probe. Ash samples were analyzed by scanning electron microscopy linked with energy-dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD) to obtain the microstructure, semiquantitative chemical composition, and mineralogy of the ash deposits. Commercial thermochemical software (FactSage) was used to calculate the thermal equilibrium and obtain the molten slag fraction and viscosity of the deposit. The process of ash deposition can be divided into four stages according to different growth rates. The shedding deposit from the probe at high temperature (probe 1) belonged to ductile deposits, while the shedding deposits from the probe at low temperature (probe 2) were brittle deposits. The duration of deposit shedding from probe 1 was about 4 mm, while it lasted a few seconds for probe 2. For probe 2, the time required to build up a new deposit and shed it was 45 min. The stable heat flux through probe 2 was 180 kW/m(2), and the decreasing heat flux of the initial layer was about 100 kW/m2. It was important to remove the initial layer when conducting artificial shedding. Different sootblowing media were used for removal of ductile deposits and brittle deposits. The SEM-EDX results showed that the shedding deposit originated in the sintered layer, which was confirmed by the XRD analysis results. The main shedding mechanism at high temperature was falling of molten ash deposits. Erosion and thermal shock were the main reasons for deposit shedding at a low temperature. The viscosity of the deposit was a key factor in the deposit shedding process.

THE DEVELOPING AND APPLICATION OF A HEAT FLUX PROBE WHEN ASH DEPOSITING

Simulation of ash depositing in heat transfer surface with heat flux probe

THE ELECTRON PROBE ANALYSIS OF MINERAL ELEMENTARY DISTRIBUTION AT ASH DEPOSITION FROM FURNACE

EXPERIMENTAL STUDY OF ASH DEPOSIT DURING CO-FIRING SAWDUST AND COAL

Simulating growth of ash deposit in boiler heat exchanger tube based on CFD dynamic mesh technique

In Situ Diagnostics on the Dynamic Processes of Ash Deposit Formation, Shedding, and Heat Transfer in a Self-Sustained Down-Fired Furnace

Test device and method for simulating deposition of fly ash on heating surface

An Experimental Investigation into the Characteristics and Deposition Mechanism of High-Viscosity Coal Ash

Research on the Dynamic Characteristic of Ash Deposition in Boilers Burning Coal and Coal Water Slurry

Influence of Ash Characteristics on Ash Deposition in Coal Fired Boiler

Development of an Online Ash-Deposition Thermogravimetric Analyzer for Pulverized Coal Combustion

Experimental measurement of the effective thermal conductivity of ash deposit for high sodium coal (Zhun Dong coal) in a 300 KW test furnace

The electron microscopy study of ash deposition in the pulverized-coal burned

Simulation of Ash Deposition in Different Furnace Temperature with a 2D Dynamic Mesh Model

A MODEL FOR PREDICTING HEAT TRANSFER PROCESS WITH COAL ASH DEPOSITION IN UTILITY BOILERS

STUDY ON MIGRATION AND DEPOSITION BEHAVIOR OF MINERAL SUSTANCES IN COAL BURNING INSIDE THE FURNACE

Dynamic behavior of biomass ash deposition in a 25 kW one-dimensional down-fired combustor

Experimental study on ash deposition and corrosion in a CFB boiler co-firing biomass with coal

Ash deposit shedding during Co-combustion of coal and rice hull using a digital image technique in a pilot-scale furnace

Experimental Investigation of the Growth of Ash Deposits with and Without Additives Through a Digital Image Technique

Numerical Simulation of Fly Ash Deposition in Coal and Corn Stalk Co-Combustion with Dynamic Mesh Technique