The Design of ESP based on USB Interface

宋玉春,许伦辉

DOI: https://doi.org/10.3969/j.issn.1674-9669.2003.01.014

2003-01-01

Abstract:In this paper, the electrostatic precipitation (ESP) control system is introduced by using of universal serial bus (USB), a new technology about interface in computer. It is included the design of system hardware, firmware, USB interface driver and application.

What problem does this paper attempt to address?

Design of Data Communication Interface of Data Acquirement System Based on USB

陈章位,赵玉刚

DOI: https://doi.org/10.3321/j.issn:1004-132X.2004.20.014

2004-01-01

Abstract:An interface based on USB is designed for Data Acquirement System with DSP chips. Cypress EZ-USB technology and FPGA technology were used in this interface. This kind of interface can achieve high speed data communication between the Data Acquirement System and the PC in the USB 1.1 protocol, and it can meet the requirements of high speed and real-time requirements.
Research on USB Data Transmission Technology Based on LabVIEW

程龙飞,何闻

DOI: https://doi.org/10.3969/j.issn.1001-3881.2009.07.036

2009-01-01

Abstract:The USB data transmission technology based on LabVIEW was studied.The USB interface circuit which core chip is PDIUSBD12 produced by PHILIPS,the firmware programming method of the USB interface circuit,and the specific method of compiling application which is based on the LabVIEW were introduced.The result in the data transmission test shows that it can realize the data transmission between superior monitor and inferior computer by using LabVIEW and USB interface.
Real-time Bidirectional Data Transmission Based on USB Interface

Kuang Wang

2005-01-01

Abstract:The article designs a real-time bidirectional transmission channel.And it introduces the theory of the design,selects specific chip,introduces the hardware of the channel,and brings forward the method of designing USB firmware,driver,and application.
Design of Phase Locked Loop Applying to USB Full Speed Equipment

Xu JIANG,Hai-bin SHEN

DOI: https://doi.org/10.3969/j.issn.1000-7024.2013.06.069

2013-01-01

Abstract:To solve the problem that we always need external crystal to provide clock for the chip in the USB full speed equipment,an implemented method of low power consumption phased locked loop(PLL) applying to the USB full speed equipment is proposed.According to the data transmission rate in the USB full speed equipment,based on the standard phase locked loop structure,a clock information extraction unit and a low power control module are added,an improved phase frequency detector(PFD) and differential voltage controlled oscillator(VCO) is implemented to the proposed phase locked loop.And the phase locked loop layout is completed with 0.35 μm technology.Furthermore,the performance of proposed phase locked loop is verified,and the results meet the requirement of the USB protocol.
Design of All-digital Clock Recovery Unit Based on USB Device

ZHANG Jun,SHEN Hai-bin

DOI: https://doi.org/10.3969/j.issn.1000-3428.2012.14.069

2012-01-01

Abstract:This paper designs a kind of all-digital clock recovery unit based on USB full speed device to solve the problem that common clock recovery methods in USB full speed device are low accuracy or high cost.This clock recovery unit contains a module which can extract timing messages from USB bus data,and uses the digitally-controlled oscillator which can overcome the bad effect by the chip's different operating conditions.The design uses the all-digital circuit design processes,logic synthesis and P&R process of which is based on the standard cell library.The result of this design satisfies the USB specification's requirements.
Design and Implementation of the High-Performance Link Layer in High-Speed Serial Communication

Yong-jian TANG,Le-nian HE,Xiao-lang YAN

DOI: https://doi.org/10.3969/j.issn.1000-7180.2005.04.037

2005-01-01

Abstract:The USB2.0 supports the high-speed signaling at 480 Mbps. It can meet the needs of image and voice signal transmitting. In this paper, after demonstration of the characters and functions of high speed digital circuit of USB2.0 link layer, a novel design and implementation method of data recovery circuits, which is based on all digital phase-looked loop (ADPLL), for the full-speed mode, as well as a new approach of parallel implementation of the encode/decode module in high-speed mode were proposed. The simulation results indicated that the circuit has reached 480MHz. A FPGA hardware simulation system was developed, in which the functions of link layer was verified.
Design and Realization of Low Cost USB Protocol Converter

杨章顺,冉立新

DOI: https://doi.org/10.3969/j.issn.1000-3428.2004.18.069

2004-01-01

Abstract:USB has become popular due to its high speed, plug and play feature and the capability to avoid resource conflict. An embedded converter from other low speed bus to USB is very interesting, since it would allow legacy peripheral devices to experience USB advantages without major changes. The paper presents a universal USB1.1 protocol converting scheme, and an example of PS/2-USB converter is also given.
Design of Visual Inspection System Based on DSP and USB Interface

边绍辉,蔡晋辉,周泽魁,张光新

DOI: https://doi.org/10.3969/j.issn.1000-3428.2004.20.074

2004-01-01

Abstract:A bottleneck of the real-time vision inspection system is the lower image processing velocity. DSP technology is applied to the field of computer vision. A USB based embedded vision inspection system using DSP and FPGA is discussed. And also, the configuration and the workflow of the system are presented in great detail.
A Data Acqusition System Based on DSP and USB

JIANG Chao,LI Pei-yu

DOI: https://doi.org/10.3969/j.issn.1001-3881.2005.01.057

2005-01-01

Abstract:The structure of a data acquisition system based on DSP and USB chips was described.The interface between different modules was introduced,and the design of firmware used in USB was described.
Design of USB Floppy Driver Based on WinCE

Ding Wei,Lü Liang,Zhao Guangzhou

DOI: https://doi.org/10.3969/j.issn.1000-0380.2009.03.005

2009-01-01

Abstract:Aiming at the problem of the currently popular embedded operating system WinCE.NET,that is not fully supporting USB floppy driver,an implementing strategy for USB floppy based on WinCE.NET is put forward.By adopting stream interface driver model,the USB floppy driving program is developed;The control of USB floppy is implemented with UFI technology.The method and whole procedures for formatting USB floppy are given;the program has been applied successfully in ARM9-based multi-functional computerized embroidery machine.The program is simple and easy to use;it is good reference for developing driving program for similar USB devices.
Design and Implementation of Infrared Data Transmission System Based on USB 2.0

张君怡,王海明,裴东兴

DOI: https://doi.org/10.3969/j.issn.1674-6236.2009.12.018

2009-01-01

Abstract:In order to overcome the deficiency or defect of wire transmission and avoid damaging the measurement equipment because of frequent pluging and drawing,the infrared data transmission system based on USB2.0 are designed in the paper.The overall structure and design and implementation of key hardware are described in detail,and the design of firmware,driver program and application program are also expatiated.It utilizes USB2.0 technology and infrared transmission technology to realize the wireless data transmit between measurement equipment and PC.
A Novel Physical-Layer Transceiver Used in USB2.0 Serial Data Link

Li Haoliang,He Lenian,Wang Zi,Yan Xiaolang

DOI: https://doi.org/10.1007/s11767-004-0246-4

2006-01-01

Abstract:The paper proposes a novel transceiver in physical layer for high-speed serial data link based upon Universal Serial Bus (USB) 2.0, comprising transmitter and receiver. In the design, transmitter contains pre-and-main driver to satisfy slew rate of output data, receiver includes optimized topology to improve precision of received data. The circuit simulation is based on Cadence’s spectre software and Taiwan Semiconductor Manufacture Corporation’s library of 0.25μm mixed-signal Complementary Metal-Oxide Semiconductor (CMOS) model. The front and post-simulation results reveal that the transceiver designed can transmit and receive high-speed data in 480Mbps, which is in agreement with USB2.0 specification. The chip of physical-layer transceiver has been designed and implemented with 0.25μm standard CMOS technology.
Interface Design Between USB and EPP

王哲,于慧敏

DOI: https://doi.org/10.3969/j.issn.1003-353x.2004.05.031

2004-01-01

Abstract:Cypress Semiconductor’s EZUSB FX used as USB controller is introduced, andthe difference between EZUSB FX and other USB controller is given. Then the convenience ininterface design between USB and other protocols is shown. At last a designed example betweenUSB and EPP protocol is presented.
Implementation of an interface card of a position control system based on USB 2.0 bus

Wang Peng,Dong Jingxin,Zhao Changde

DOI: https://doi.org/10.3969/j.issn.1002-4956.2011.08.027

2011-01-01

Abstract:For the purpose of making students handle the technology of computer controlling,an interface card is designed with EZ-USB FX2LP,which is used in the Computer Controlling System class.The card includes interface to USB 2.0 bus,sample pulse generator,counter of position,D/A,etc.It can support students to realize kinds of controlling methods through programming on computer,so to solidify the knowledge of computer controlling.
In System Programming Design of 51 Microcontroller Base on USB Interface

Chen Zhi-ying

Abstract:The paper presents a design of 51 microcontroller AT89S51/52/53 in system programming base on USB interface,emphasis on the hardware design of USB-SPI interface circuit and the design of PC software for microcontroller programming by VB.The design has many advantages such as small size,low power consumption,high reliability etc.It is very valuable in the applications of 51 microcontroller and is worth references as well.

Computer Science,Engineering
Design and Implementation of USB1.1 Controller

Ying-ke GU,Zheng WANG,Guo-qiang BAI,Hong-yi CHEN

DOI: https://doi.org/10.3969/j.issn.1000-3428.2009.02.083

2009-01-01

Abstract:This paper designs and implements an Universal Serial Bus(USB)1.1 controller.It supports control,interrupt and bulk mode at full speed.The number of the endpoints of this IP is configurable.The IP works in a security chip and it breaks some of the bottleneck of the chip I/O communications.An FPGA verification platform is built with this USB 1.1 device IP and MCU 8051,and it can communicate with the PC.Other function modules in the security chip are tested on this platform.
Universe Serial Bus (USB)

黄维柱,许军

DOI: https://doi.org/10.3969/j.issn.1001-3695.2001.02.015

2001-01-01

Abstract:Traditional interfaces of external peripherals have manyshortcomings，so they are not consistent with the requirements of the PC now. The newly-come Universal Serial Bus has many advantages, such as: high speed, ease-of-use, ease to expand port, supporting plug-play, low-cost etc, so it is used very widely now. This paper just describes some main features of USB.
System-Efficient ESD Design Based on a Modular Measurement System Applied to USB

Lucas Speckbacher,David Johannes Pommerenke,Gabriel Fellner,Lukas Pertoll,Harald Gossner

DOI: https://doi.org/10.1109/tim.2024.3497173

IF: 5.6

2024-11-29

IEEE Transactions on Instrumentation and Measurement

Abstract:A modular system-level electrostatic discharge (ESD) evaluation platform is described. It forms a flexible instrument that allows the investigation of the impact of various system-level and printed circuit board (PCB) ESD design choices. The transmission line pulse (TLP) and IEC 61000-4-2 pulse behavior of a universal serial bus (USB) 3.0 redriver IC protected by different transient voltage suppressors (TVSs) are investigated. The system includes modules with varying functionality which can be flexibly combined on a baseboard. IV curves, leakage current, S-parameters, USB data errors, and IC power consumption can be monitored to detect damage or soft-fail disturbances. We report on the ESD protection achieved with two types of TVS: TVS with and without snap-back characteristics. The measured voltages and currents are compared to a system-efficient ESD design (SEED) simulation. This modular system allows rapid implementation of complex experimental characterization setups to investigate system-level ESD response, providing essential input to improve design robustness using the SEED modeling concept.

engineering, electrical & electronic,instruments & instrumentation
Hardware interface design of high-speed communication module in ECT system

Zheng Weijun,Wang Baoliang,Huang Zhiyao,Li Haiqing

DOI: https://doi.org/10.3321/j.issn:0254-3087.2006.z1.246

2006-01-01

Abstract:Design of high-speed communication module based on USB2.0 is described.The interface between CY7C68013 which works in slave FIFO mode and DSP is given.And details of some key pins and several points of PCB design are explained.
Design of Data Transmission System Based on FPGA and USB 2.0

Junsheng Wu,Fuzhou Shang,He Sun,Tian Qin,Qing Li

DOI: https://doi.org/10.4028/www.scientific.net/amm.321-324.417

2013-01-01

Applied Mechanics and Materials

Abstract:In this paper, a high-speed data transmission system based on FPGA (Field Programmable Gate Array) and USB 2.0 (Universal Serial Bus) technology is designed. Firstly, we introduce the hardware of the data transmission system, which includes data acquisition circuit, transmission circuit and power conversion circuit, etc. Secondly, the corresponding software design including USB firmware program, USB driver and firmware modification are described in detail. Finally, the corresponding experiment has been carried out, which show that the developed system will help to achieve the data transmission system with the characteristics of high-speed, integration and low power consumption, etc.

The Design of ESP based on USB Interface

Design of Data Communication Interface of Data Acquirement System Based on USB

Research on USB Data Transmission Technology Based on LabVIEW

Real-time Bidirectional Data Transmission Based on USB Interface

Design of Phase Locked Loop Applying to USB Full Speed Equipment

Design of All-digital Clock Recovery Unit Based on USB Device

Design and Implementation of the High-Performance Link Layer in High-Speed Serial Communication

Design and Realization of Low Cost USB Protocol Converter

Design of Visual Inspection System Based on DSP and USB Interface

A Data Acqusition System Based on DSP and USB

Design of USB Floppy Driver Based on WinCE

Design and Implementation of Infrared Data Transmission System Based on USB 2.0

A Novel Physical-Layer Transceiver Used in USB2.0 Serial Data Link

Interface Design Between USB and EPP

Implementation of an interface card of a position control system based on USB 2.0 bus

In System Programming Design of 51 Microcontroller Base on USB Interface

Design and Implementation of USB1.1 Controller

Universe Serial Bus (USB)

System-Efficient ESD Design Based on a Modular Measurement System Applied to USB

Hardware interface design of high-speed communication module in ECT system

Design of Data Transmission System Based on FPGA and USB 2.0