Abstract:Pure copper is very soft, however, hardening the pure copper with most strengthening mechanisms leads to a significant reduction in electrical conductivity. Grain refinement is a better strengthening mechanism to maintain high enough electrical conductivity. Plastic deformation at room temperature followed by post-annealing is one of the best methods to achieve fine-grained metals and alloys. In this research, the high-temperature annealing behavior of cold-rolled electrolytic tough-pitch (ETP) copper sheets was studied. 90 % asymmetric cold rolling followed by high-temperature post-annealing at 673 K for 1, 2, 5, 10, 30, 60, and 120 min were applied on the copper. The microstructure was significantly changed with increasing annealing time from 1 to 2 min owing to full recrystallization. With increasing the annealing duration, the grain size is increased. The formation of equiaxed grains with a smaller size (∼9 μm) compared to the full-annealed (initial) sample (∼68 μm) is observed after the longest time of post-annealing (120 min) due to the pinning effect of Cu2O particles. The post-annealed copper sheets processed by asymmetric rolling (in this work) exhibited a more homogeneous microstructure through the thickness compared to the symmetric rolling due to more uniform stored strain energy. The results showed that the first deformed grains that undergo recrystallization during post-annealing are Goss-oriented grains. With an increase in the post-annealing time, the S and Copper components were eliminated and a strong Cube and P texture orientations were formed. Interestingly, after 1 min of post-annealing, the yield and tensile strength enhanced to 410.2 MPa and 418.6 MPa owing to the annealing hardening phenomenon. The hardness and strength reached a constant value after the post-annealing for 10 min and above. With increasing the post-annealing duration, the central area of fracture surfaces (consisting of ductile dimples) became larger and the outer region (consisting of flat surfaces and shear dimples) became smaller, showing a shift towards perfect ductile fracture. With the increase of post-annealing time from 1 min to 120 min, the electrical conductivity was increased from 77.6 to 97.5 %IACS. The presence of the Cube texture increased the electron mobility compared to the P orientation, by reducing the mean distance that they can travel without scatter. From the obtained results, it can be concluded that the asymmetric cold rolling followed by high-temperature post-annealing is capable of strength improvement and maintaining electrical conductivity in copper.

High strength high conductivity copper prepared by C-ECAP and Cryo-rolling

Effect of cryogenic impact deformation and subsequent annealing on microstructure and microhardness of pure copper

High Strength and High Ductility Copper Obtained by Topologically Controlled Planar Heterogeneous Structures

Influence of Cold Rolling Routes on Mechanical Properties of Copper Subjected to ECAP

Effect of cryo-rolling on mechanical properties and microstructure of pure copper

Effect of cryogenic rolling and multistage thermo-mechanical treatment on the microstructure and properties of the Cu-0.4Cr-0.39Zn-0.1Mg-0.07Zr alloy

High-temperature annealing behavior of cold-rolled electrolytic tough-pitch copper

Experimental Study on Pure Copper Subjected to Different Severe Plastic Deformation Modes

Micro/nanostructure high strength and high conductivity CuCrZr alloy prepared through equal channel angular pressing and aging treatment

Enhanced Mechanical and Electrical Properties of Super-Aligned Carbon Nanotubes Reinforced Copper by Severe Plastic Deformation

Microstructure, texture and mechanical properties of pure copper processed by ECAP and subsequent cold rolling

Microstructural evolution and mechanical property of Cu‐Cr‐Zr‐ZrB2 composites subjected to cryorolling and aging treatment

Enhanced Tensile Ductility and Toughness in Nanostructured Cu

Low‐Temperature Annealing of Asymmetrically Cold‐Rolled Electrolytic Tough‐Pitch Copper: Anneal Hardening and Bimodal Microstructure

Improvement in Strength and Ductility of Asymmetric-Cryorolled Copper Sheets Under Low-Temperature Annealing

High Strength and High Electrical Conductivity CuMg Alloy Prepared by Cryorolling

Deformation Microstructure and Property Control of CuCrZr Alloy Directionally Solidified at Room Temperature C-ECAP

An Investigation on Rolling Texture Transition in Copper Preprocessed by Equal Channel Angular Pressing

Microstructure evolution of high-strength and ultra-high-conductivity microfilament wire prepared by continuous deformation of single-crystal copper

Microstructural Evolution and Micro‐Compression in High‐Purity Copper Processed by High‐Pressure Torsion

Microstructural Evolution and Micro/Meso-Deformation Behavior in Pure Copper Processed by Equal-Channel Angular Pressing