Abstract:In the present investigation, equiatomic CoCrFeMnNi high entropy alloy (HEA) was subjected to 80% cold rolling (as-rolled) followed by isothermal annealing treatment at 700 °C for different time periods. Microstructural characterization was performed using electron back-scattered diffraction (EBSD) and electron channeling contrast imaging (ECCI) techniques on the as-rolled and annealed samples. The as-rolled microstructure consisted of elongated grains mainly composed of strong α-fiber and weak γ-fiber textures. The as-rolled sample showed the formation of ingrain SBs in the γ-fiber grains, which served as preferential sites for grain nucleation. The annealing treatment of as-rolled samples at 700 °C cause static recovery (SRV) before 5 minutes of heat-treatment, whereas static recrystallization (SRX) was observed after 5 minutes of heat-treatment in the CoCrFeMnNi alloy samples. A faster rate of recrystallization kinetics was observed after 15 minutes of heat-treatment. The annealing treatment reduced the intensity of α-fiber and enhanced the Copper, Cube and P ({011} ) texture components. Copper components originated from coarse recrystallized grains, which were the results of localized grain growth phenomena. Unusual behavior of banded featured α-fiber grains was observed during the annealing process. These banded grains in the partially annealed samples consisted of subgrain-boundaries and showed a delayed response to recrystallization as compared to grains with other orientations. Stored energy (SE) and Taylor factor (M) calculations were also used to understand the delayed recrystallization response of the banded featured/retained deformed grains. The microhardness value of the as-rolled sample was approximately 450 Hv, which decreased to around 230 Hv for the fully recrystallized grains.

Effects of cold-rolling and subsequent annealing on the nano-mechanical and creep behaviors of CrCoNi medium-entropy alloy

Influence of annealing temperatures on the microstructure and deformation behavior of a CrCoNi based medium-entropy alloy

Effect of room temperature rolling and annealing on microstructure and mechanical properties of (CrCoNi) 96 V 4 medium entropy alloy

Effects of Thermo-mechanical Treatment on the Microstructures and Mechanical Properties of a Medium-Entropy Alloy

Significant annealing-induced hardening effect in nanolaminated-nanotwinned (CrCoNi)97.4Al0.8Ti1.8 medium-entropy alloy by severe cold rolling

Effects of cold rolling and annealing treatment on microstructure and properties of CoFeNiMnV high‐entropy alloys

Effect of Annealing Treatment on the Heterogeneous Microstructure and Properties of Cold-Rolled FeCoCrNiMn High-Entropy Alloy

Microstructure and Mechanical Properties Evolution of the Al, C-Containing CoCrFeNiMn-Type High-Entropy Alloy during Cold Rolling

Microstructural Evolution and Mechanical Properties of Al0.5CoCrFeNi High-Entropy Alloy after Cold Rolling and Annealing Treatments

Revealing the microstructural evolution and mechanism during the thermomechanical treatment of polycrystalline CrCoNi medium-entropy alloy

Preparation of high-mechanical-property medium-entropy CrCoNi alloy by asymmetric cryorolling

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Microstructure and Mechanical Property Evolution during Annealing of a Cold-Rolled Metastable Powder Metallurgy High Entropy Alloy

Microstructure and Tensile Properties of Al0.5CoCrCuFeNi Alloys Produced by Simple Rolling and Annealing

Revealing the relationship between microstructures, textures, and mechanical behaviors of cold-rolled Al0.1CoCrFeNi high-entropy alloys

Effect of Warm Rolling on the Structure and Tensile Properties of a Metastable Fe-Based Medium Entropy Alloy

Revealing the inhomogeneous nature of microstructure and texture evolution in the cold-rolled CoCrFeMnNi alloy during static recrystallization

Effect of low temperature rolling on mechanical properties and corrosion resistance of CrCoNi medium entropy alloy

Effect of Annealing Temperature on the Microstructure and Mechanical Properties of CoCrFeNiNb0.2Mo0.2 High Entropy Alloy

Improving Mechanical Properties of Fe-Mn-Co-Cr High-Entropy Alloy via Annealing after Cold Rolling

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains