Abstract:The effects of cold rolling followed by annealing on the mechanical properties and dislocation substructure evolution of undoped and 1.1 at. % carbon-doped Fe40.4Ni11.3Mn34.8Al7.5Cr6 high entropy alloys (HEAs) have been investigated. X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atom probe tomography (APT) were employed to characterize the microstructures. The as-cast HEAs were coarse-grained and single phase f.c.c., whereas the thermomechanical treatment caused recrystallization (to fine grain sizes) and precipitation (a B2 phase for the undoped HEA; and a B2 phase, and M23C6 and M7C3 carbides for the C-doped HEA). Carbon, which was found to have segregated to the grain boundaries using APT, retarded recrystallization. The reduction in grain size resulted in a sharp increase in strength, while the precipitation, which produced only a small increase in strength, probably accounted for the small decrease in ductility for both undoped and C doped HEAs. For both undoped and C-doped HEAs, the smaller grain-sized material initially exhibited higher strain hardening than the coarse-grained material but showed a much lower strain hardening at large tensile strains. Wavy slip in the undoped HEAs and planar slip in C-doped HEM were found at the early stages of deformation irrespective of grain size. At higher strains, dislocation cell structures formed in the 19 urn grain-sized undoped HEA, while microbands formed in the 23 mu m grain-sized C-doped HEA. In contrast, localized dislocation clusters were found in both HEM at the finest grain sizes (5 mu m). The inhibition of grain subdivision by the grain boundaries and precipitates lead to the transformation from regular dislocation configurations consisting of dislocation-cells and microbands to irregular dislocation configurations consisting of localized dislocation clusters, which further account for the decrease in ductility. Investigation of the formation mechanism and strain hardening of dislocation cells and microbands could benefit future structural material design. (C) 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Effects of Thermo-mechanical Treatment on the Microstructures and Mechanical Properties of a Medium-Entropy Alloy

Effect of Cold Rolling on Microstructure and Mechanical Property of a Novel (fe50mn30co10cr10)97c2mo1 High Entropy Alloy

Effects of cold‐rolling and subsequent annealing on microstructure and mechanical properties of (CrCoNi)97Al1.5Ti1.5 medium‐entropy alloy

Effect of room temperature rolling and annealing on microstructure and mechanical properties of (CrCoNi) 96 V 4 medium entropy alloy

Effect of Thermomechanical Processing on Microstructure and Mechanical Properties of CoCrFeNiMn High Entropy Alloy

Microstructures and deformation mechanisms of the medium-entropy alloy (NiCoCr)76(Ni6AlTi)3

Influence of annealing temperatures on the microstructure and deformation behavior of a CrCoNi based medium-entropy alloy

The Effect of Carbon on the Microstructures, Mechanical Properties, and Deformation Mechanisms of Thermo-Mechanically Treated Fe40.4Ni11.3Mn34.8Al7.5Cr6 High Entropy Alloys

Effects of cold-rolling and subsequent annealing on the nano-mechanical and creep behaviors of CrCoNi medium-entropy alloy

Thermal stability of microstructure and their influences on mechanical properties of precipitation-hardened medium-entropy alloy Ni43.4Co25.3Cr25.3Al3Ti3

Microstructure and Properties of Bulk Al0.5CoCrFeNi High-Entropy Alloy by Cold Rolling and Subsequent Annealing

Microstructure and properties of bulk Al 0.5 CoCrFeNi high-entropy alloy by cold rolling and subsequent annealing

Effects of Heat Treatment on the Microstructure and Properties of Cold-Forged CoNiFe Medium Entropy Alloy

Mechanical Behaviors of Cold-Rolled and Subsequently Annealed Fe35Ni35Cr20Mn10 High-Entropy Alloy

Effects of Post Annealing on the Microstructure, Precipitation Behavior, and Mechanical Property of a (cocrni)94al3ti3 Medium-Entropy Alloy Fabricated by Laser Powder Bed Fusion

Precipitation and heterogeneous strengthened CoCrNi-based medium entropy alloy with excellent strength-ductility combination from room to cryogenic temperatures

Studying the Effect of Cold Rolling and Heat Treatment on the Microstructure and Mechanical Properties of the Fe36Mn20Ni20Cr16Al5Si3 High Entropy Alloy

Investigation on Microstructure, Superior Tensile Property and Its Mechanism in Al0.3CoCrFeNi High-Entropy Alloy Via Thermo-Mechanical Processing

Mechanical Properties and Microstructure Evolution of a CrCoNi Medium Entropy Alloy Subjected to Asymmetric Cryorolling and Subsequent Annealing

Effect of Rolling on the Microstructure and Mechanical Properties of (fecrni)94ti3al3 Medium Entropy Alloy Fabricated Via Selective Laser Melting

Effect of Rolling Temperature and Subsequence Ageing on the Mechanical Properties and Microstructure Evolution of an Al-Cu-Li Alloy