Abstract:A major remaining challenge for $Nb_3Sn$ high field magnets is their training due to random temperature variations in the coils. The main objective of our research is to reduce or eliminate it by finding novel impregnation materials with respect to the epoxies currently used. An organic olefin-based thermosetting dicyclopentadiene (DCP) resin, $C_10H_12$, commercially available in Japan as TELENE by RIMTEC, was used to impregnate a short $Nb_3Sn$ undulator coil developed by ANL and FNAL. This magnet reached short sample limit after only two quenches, compared with several dozens when $CTD-101K$ was used. Ductility, i.e. the ability to accept large strains, and toughness were identified as key properties to achieve these results. In addition, we have been investigating whether mixing TELENE with high heat capacity ceramic powders, increases the specific heat ($C_p$) of impregnated $Nb_3Sn$ superconducting magnets. The viscosity, heat capacity, thermal conductivity, and other physical properties of TELENE with $high-C_p$ powder fillers were measured in this study as a function of temperature and magnetic field. Mixing TELENE with either $Gd_2O_3$, $Gd_2O_2S$, and $HoCu_2$ increases its $C_p$ tenfold. We have also investigated the effect on the mechanical properties of pure and mixed TELENE under 10 $Gy$ of gamma-ray irradiation at the Takasaki Advanced Radiation Research Institute in Takasaki, Japan. Whereas both $TELENE-82wt\%Gd_2O_3$ and $TELENE-83wt\%HoCu_2$ performed well, the best mechanical properties after irradiation were obtained for $TELENE-87wt\%Gd2O_2S$. Testing a short undulator in the future with the latter impregnation material will verify whether it will further improve the coils thermal stability. Short magnet training will lead to better magnet reliability, lower risk and substantial saving in accelerators commissioning costs.

Training-free demonstration of a 5.4 T Nb 3 Sn canted-cosine-theta accelerator dipole impregnated with paraffin wax

Assessment of Training Performance, Degradation and Robustness of Paraffin-Wax Impregnated Nb 3 Sn Demonstrator under High Magnetic Field

Training performance of Nb3Sn Rutherford cables in a channel with a wide range of impregnation materials

Improved training in paraffin-wax impregnated Nb3Sn Rutherford cables demonstrated in BOX samples

Training-free performance of the wax-impregnated SuShi septum magnet

Test samples and infrastructure for accelerator magnet developments

Minimum Quench Energy Of Nb$_3$Sn Wires With High Specific Heat Tape

Commissioning, Performance, and Effect of the Quench Current-boosting Device on a Dedicated Superconducting Magnet

A New Ductile, Tougher Resin for Impregnation of Superconducting Magnets

Development of a 1/2-length prototype high field Nb3Sn magnet for the 4th generation ECR ion source

Optimizing the use of pressurized bladders for the assembly of HL-LHC MQXFB magnets

Performance of a MQXF Nb3Sn Quadrupole Magnet Under Different Stress Level

Conceptual Design of an HTS Dipole Insert Based on Bi2212 Rutherford Cable

Design and Assembly of a Large-aperture Nb3Sn Cos-theta Dipole Coil with Stress Management in Dipole Mirror Configuration

Simulation of Thermo-Mechanical Stresses After a Quench in the 15 T Test Facility Dipole Magnet

Design and Testing of a Prototype Canted-Cosine-Theta HTS Dipole Magnet Using CORC Cable

Re-assembly and test of a COMB dipole magnet with STAR wires

First results of AUP Nb3Sn quadrupole horizontal tests

The first superconducting final focus quadrupole prototype of the FCC-ee study

A Combined Testing and Modelling Methodology for the Mechanics of High-Field Superconducting Magnets