Abstract:Abstract A high temperature superconducting (HTS) demonstration coil has been developed in the frame of the Experimental Physics department Research & Development program at CERN. The magnet extends the recent experimental demonstration of aluminium-stabilised HTS conductors and supports the development of future large scale detector magnets. The HTS magnet has five turns and an open bore diameter of 230 mm. Up to 30 K, the coil was measured to be fully superconducting across four central turns at 4.4 kA, the maximum available current of existing power supply. The central magnetic field is 0.113 T,the peak field on the conductor is 1.2 T and the coil has a stored magnetic energy of 0.1 kJ. A 3D-printed aluminium alloy (Al10SiMg) cylinder acts both as a stabiliser and a mechanical support for the superconductor. The resistivity of Al10SiMg was measured at cryogenic temperatures, and has a residual resistivity ratio of approximately 2.5. The ability to solder ReBCO tapes (a stack of four REBCO tapes, 4 mm wide, Fujikura) to Al10SiMg stabiliser, electroplated with copper and tin, forming a coil, is demonstrated using tin-lead solder at 188 °C. The HTS magnet was proven to be stable when superconductivity was broken locally using a thin-film heater. Despite voids in the solder joint between HTS and stabiliser, no degradation of the magnet’s performance was observed after 12 thermal cycles and locally quenching the magnet. A numerical model of the transient behaviour of solenoid with partially shorted turns is developed and validated against measurements. Our work experimentally and numerically validates that using an aluminium alloy as a stabiliser for HTS tapes can result in a stable, lightweight and transparent magnet.

Training-free performance of the wax-impregnated SuShi septum magnet

Training-free demonstration of a 5.4 T Nb 3 Sn canted-cosine-theta accelerator dipole impregnated with paraffin wax

Development of a 1/2-length prototype high field Nb3Sn magnet for the 4th generation ECR ion source

Design and Test of A Short Mockup Magnet for the Superconducting Undulator at the Ssrf

Assessment of Training Performance, Degradation and Robustness of Paraffin-Wax Impregnated Nb 3 Sn Demonstrator under High Magnetic Field

NbTi/Nb/Cu multilayer shield for the superconducting shield (SuShi) septum

Commissioning, Performance, and Effect of the Quench Current-boosting Device on a Dedicated Superconducting Magnet

Magnetic Field Analysis and Measurement of Pulsed Septum Magnet

The first superconducting final focus quadrupole prototype of the FCC-ee study

Optimizing the use of pressurized bladders for the assembly of HL-LHC MQXFB magnets

Analysis of the mechanical performance of the 4.2 m long MQXFA magnets for the Hi-Lumi LHC Upgrade

Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet with Graded Common-Coil Configuration

Full Power Test of Superconductor of BESIII Magnet

Conceptual designs of dipole magnet for muon collider ring

Self-protected high-temperature superconducting demonstrator magnet for particle detectors

Electromagnetic, stress and thermal analysis of the Superconducting Magnet

Conceptual Design Study of a Large Bore Superconducting Test Facility Magnet, SUCCEX

Improved training in paraffin-wax impregnated Nb3Sn Rutherford cables demonstrated in BOX samples

First performance test of a 25 T cryogen-free superconducting magnet

Design and Testing of a Prototype Canted-Cosine-Theta HTS Dipole Magnet Using CORC Cable

Powering Tests Results of the First Batch of MCBXFB Magnets Produced in Industry