Abstract:Nb3Sn conductors are important candidates for high-field magnets for particle accelerators, and they continue to be widely used for many laboratory and NMR magnets. However, the critical current density, Jc, of present Nb3Sn conductors declines swiftly above 12-15T. State-of-the-art Ta- and Ti-doped strands exhibit upper critical field, Hc2, values of 24-26.5T (4.2K) and do not reach the FCC target Jc, which serves as the present stretch target for Nb3Sn development. As recently demonstrated, to meet this goal requires enhanced vortex pinning but an independent and supplementary approach is to significantly enhance Hc2. In this study, we have arc-melted multiple Nb alloys with added Hf, Zr, Ta and Ti and drawn them successfully into monofilament wires to investigate the possibilities of Hc2 enhancement through alloying. Hc2(T) was measured for all samples in fields up to 16T and some up to 31T. We have found that all alloys show good agreement with the standard Werthamer, Helfand, and Hohenberg (WHH) fitting procedure without the need to adjust the paramagnetic limitation parameter (alpha) and spin-orbit scattering parameter (lambda_so). The evaluation of dHc2/dT near Tc, which is proportional to the electronic specific heat coefficient (gamma) and the normal state resistivity (rho_n), allows a better understanding of the induced disorder introduced by alloying in the A15 phase. So far, we have observed that Hf alloying of pure Nb can enhance Hc2(0) by 3-4T to 28T, while adding just 1 at. %Hf or Zr into a Nb4Ta base alloy can raise Hc2(0) to 31T. Very importantly we find that Hf and Zr raise the alloy recrystallization temperature above the usual A15 reaction temperature range of 650°C-750°C, thus ensuring denser A15 phase nucleation in the Nb alloy grain boundaries, possibly leading to a more homogeneous A15 phase Sn content and refined A15 grain size. The potential for...

Minimum Quench Energy Of Nb$_3$Sn Wires With High Specific Heat Tape

Training-free demonstration of a 5.4 T Nb 3 Sn canted-cosine-theta accelerator dipole impregnated with paraffin wax

Training performance of Nb3Sn Rutherford cables in a channel with a wide range of impregnation materials

Assessment of Training Performance, Degradation and Robustness of Paraffin-Wax Impregnated Nb 3 Sn Demonstrator under High Magnetic Field

A new ductile, tougher resin for impregnation of superconducting magnets

Conceptual Design of an HTS Dipole Insert Based on Bi2212 Rutherford Cable

Internally Oxidized Nb3Sn Strands with Fine Grain Size and High Critical Current Density

Determination of the electromechanical limits of high-performance Nb$_3$Sn Rutherford cables under transverse stress from a single-wire experiment

Deformation Behavior and Degradation on Rutherford Cabling of Nb 3 Sn Wires

Enhanced Magnetocaloric Performance in Nanocrystalline/amorphous Gd3Ni/Gd65Ni35 Composite Microwires

Influence of Nb Alloying on Nb Recrystallization and the Upper Critical Field of Nb3Sn

Improved training in paraffin-wax impregnated Nb3Sn Rutherford cables demonstrated in BOX samples

Research on Insulation Technology for Nb3Sn Layer Coil of Superconducting Conductor Testing Facility

Thermal Conductivity of Industrial Nb3Sn Wires Fabricated by Various Techniques

Study on the High Temperature Heat Treatment Process Optimization of Different Sizes High Jc Nb 3 Sn Wire Produced by WST

Modeling heat transfer from quench protection heaters to superconducting cables in Nb3Sn magnets

A Novel Aluminum-Stabilized Stacked REBCO Tape Cable

Internal Strain Measurement by Neutron Diffraction Under Transverse Compressive Stress for Nb 3 Sn Wires With and Without Cu-Nb Reinforcement

Nb3Sn wire shape and cross sectional area inhomogeneity in Rutherford cables

Thermomechanical Behavior of the HL-LHC 11 Tesla Nb3Sn Magnet Coil Constituents during Reaction Heat Treatment