Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Preparation of a C/C–Cu Composite with Mo2C Coatings As a Modification Interlayer

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Enhanced softening resistance and mechanical properties of Mo 2 C particle-reinforced Cu-matrix composites

Understanding wetting mechanism of pure Cu on C/C composites modified by chromium carbide

Preparation and properties of W-Mo-Cu composite using solution combustion synthesized W Mo solid solution nanopowder

Preparation of high thermal conductivity copper–diamond composites using molybdenum carbide-coated diamond particles

Chemically dealloyed Mg–Cu alloy lamina as an interlayer for reinforcing a C/C composite – TC4 alloy vacuum brazed joint

Improvement of interfacial interaction and mechanical properties in aluminum matrix composites reinforced with Cu-coated carbon nanotubes

Mo 2 C interface layer: effect on the interface strength and cutting performance of diamond/Fe-Ni-WC composites

New Preparation Technology of Copper Matrix Composites Reinforced by Short Carbon Fibers

Study on the tribological properties of MoB/Cu laminated composite materials fabricated by hot-pressing process

Preparation of laminated Cr3C2/Cu composites by direct ink writing and pressureless infiltration

Effect of Cu coating thickness on carbon fiber surface on microstructure and mechanical properties of carbon fiber reinforced aluminum matrix composites

Microstructure and mechanical behavior of carbon fiber reinforced carbon, silicon carbide, and copper alloy hybrid composite fabricated by Cu-Si alloy melt infiltration

Study on Metallurgically Prepared Copper-Coated Carbon Fibers Reinforced Aluminum Matrix Composites

Progress of CNTs Reinforced Copper-based Composite Preparation

A Powder Metallurgy Route to Fabricate CNT-reinforced Molybdenum-Hafnium-carbon Composites

Formation Mechanism of W-coated Cu Composite Powders and the Metal Injection Molding Using Polyoxymethylene-Based Binders

Enhancing the physical properties of Mo-Cu composites through plasma spheroidized spherical molybdenum powder

Improving comprehensive performance of copper matrix composite by spray pyrolysis fabricated CNT/W reinforcement

Effect of copper coating on interfacial properties, interfacial thermal resistance, microstructure evolution and mechanical properties of aluminum matrix composites